Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hello,
We are experiencing an issue when putting the nRF52840 back to a low-power state after having had UART configured for double buffering. For context we are using nRF5...
Hello support Team,An unclear point came out when driving nRF52810 with Keil uVision5. I have a soft device(S112) write error. Can you help me with the following information...
Hello, Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0
I made my app_error_fault_handler. It is very good for me.
I sometimes got an error. So I saw that log...
I didn't change the sample code. Why does the build fail?
1> Compiling ‘main.c’ 1> ../src/main.c:60:28: error: 'DT_ALIAS_LED0_GPIOS_PIN' undeclared here (not in a function...
Hi,
I am implementing a background DFU bootloader and uses the example from Vidar Berg ( https://devzone.nordicsemi.com/f/nordic-q-a/46994/background-dfu-application-source...
Hi,
I have just updated my app from SDK 15.2 to 15.3 (and the softdevice from 6.1.0 to 6.1.1).
Now nothing is working... I initializes a button with NRFX_GPIOTE and now...
Trying to set up attribute reporting I thought I had found a solution but was apparently wrong. My coordinator is sending an attribute reporting request with a minumum reporting...
Hello,
I'm using nRF52832 in a sensor PCB card, and I want it to have an antenna. Now I'm drawing the schematics of the PCB using KiCad, but there is one problem I can't...
Hello Nordic team,
Sorry for the ambiguous question. Let me know if you need further clarification about the question.
Currently we have a nRF52 based HID device....
Now that nrfutil has been ported to Python 3, I've been trying to get a DFU controller set up on a Raspberry Pi 3A running Raspbian Lite. I've built and installed the pc-ble...
Hello,
I have a query regarding the exponential waiting period behaviour when pairing fails under repeated attempts. In the Bluetooth Core Spec v5.1 Vol 3, Part H, Section...
Hi, Nordic!
We have connected gpio pins to usb data line pins for using usb or i2c in different times.
But even if USB core disconnected, usb lines hinder for i2c lines...
Hi;
I am trying to send a Telegram message using Telegram Bot API . As the documentation shows: "All queries to the Telegram Bot API must be served over HTTPS". I have...
Hello,
We are using NRF52840 and for a specific use case we will install our module on an M.2 (A/E) breakout. In this configuration USB will be the main communication interface...
Hello,
We made a small replacement on the event handler of the ble_central/ble_app_uart_c application, just to do a loopback to test the UART module.
Here is how the...
