Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Hi,
I'm trying to validate a device which uses VSP to communicate. It has a custom service with only 2 characteristics. 1 to Write (TX) and the other Notifies (RX).
When...
Hello :
I come from STM32 programming and I am new to Nordic device programming.
for nRF52840 DK, I am looking at the ble-blinking example and try to understand Softdevice...
i am working nrf51822 and SDK V10 SoftDevice S110. I was using some old version of nrfutil ( dont know version ) to generate zip file, that was working fine. when i start...
Is there a way using the API to utilize all 31 bytes of advertisement data for a user application? I'm porting an application, which sends data in advertisement packets, to...
Hi,
I need nrf_malloc and nrf_free for my application but I cant find which files should I include to be able to use thees functions.
Thank you very much
Hi,
I would like to evaluate the long range demo with the 15.2 SDK (original 15.0 is used). Opening the project and trying to compile it gives some errors like "no such...
Hi support team,
I have found that RESN and RESP are typically 160 ohms, customer would like to know their stability and temperature coefficient.
Regards
Salas
HI,
Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to change my device name by writing data from bluetooth
when getting 0xdd 0x06 ........,it...
Hi What is the minimum clock frequency that the TWIS module will work with? Obviously the I2C spec minimum is about 100kHz however the device I am communicating with is using...
Hi,
Is it possible to use the modem firmware mfw_nrf9160_1.1.1 (delivered with nRF Connect SDK 1.2) with nRF Connect SDK 1.1?
We will move to nRF Connect SDK 1.2, but...
Hello, we are integrating a BLE board (nrf52832) into our system, and the ble_app_uart example project is perfect for us, so we are starting with that.
What we are seeing...
After reading some questions about the Thingy:91 here in the forum, I start asking myself, if the Thingy:91 without a nRF9160 DK is usable at all.
Any experience with that...
Hi, I'm working on a design with nRF52832 + chip antenna. I'd like to add a PI network to be able to tune the antenna before production.
I'm working with this antenna:...
OK, I have an app that succeeds in starting advertising and then arrives in the main event loop, following which I go to the NRF_BREAKPOINT_COND trap.
Since I do not have...
hi,
I am using Running Speed and Cadence Service structure, when i raise a write command (bt_gatt_write) from the client I was expecting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
