Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
While the softdevice is active (nRF51822) available interrupt priorities are:
typedef enum {
NRF_APP_PRIORITY_HIGH = 1,
NRF_APP_PRIORITY_LOW = 3
} nrf_app_irq_priority_t;...
Hi all,
I'm trying to use NRF24L01, using REUSE_TX_PL command,
the data sheet says as long as CE keep high, the chip will transmit the payload continuously, what i wondering...
Hi
Did you have tested the power current of nRF24LU1 when RF was off and USB worked normally?
We want it less than 4mA. Could you have any idea to make it? Thanks.
Hello! I am trying to develop on the nRF51822 eval board as called PCA10001. The programming interface I use is uVision4 on win7.
I would set a static PASSKEY for the pairing...
When I successfully bond with an Android device, then disconnect the Android device, the following attempt to re-connect fails. It appears the chip enters some internal error...
Hi,
after i get eclipse to debug (thanks to cocoa) i need to make a new project. What option i have to choose, to create a new project to run it on my nrf51822 evalboard...
In the nRF51 reference manual, page 59 shows the config value for pullup is 2 (upshift by 2)
In the file nrf51.bitfields.h, at line 2339, we have:
#define GPIO_PIN_CNF_PULL_Pullup...
Hi,
I'd like to add some custom data (25 octets) to the nRF8002 advertisement packets, using the vendor specific data type (FF).
Is this possible in some way or do we...
Hi, I am trying to enabling a notification of an attribute(once the attribute changed, the server will push the new value to the client) and I learned I have to first configure...
What's the proper way to implement bonding that depends on proximity (rather than a whitelist)? So when the client (phone) is close (say, five to ten centimeters) to the server...
I download uart sample from Nordic developer zone . at devzone.nordicsemi.com/.../is-there-a-serial-port-profile-for-ble
Because you had build the uart profile and iOS...
Hi,
I just started with the nrf 51822 eval kit. I've used keil before and am using the evaluation version. The Blinky example compiles, uploads and can debug fine (step...
