Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, I am trying to get RSSI values using BLE module on nRF52840(pca20035). But I could not see possible way to get the RSSI values on Nordic Thingy91(nRF9160) Please map me...
hi all
i want porting qpc with softdevice. it need set SCB_SYSPRI exception priorities with PRIMASK bit or the BASEPRI register for critical section
can anyone give me...
Hello,
I would like to update an nrf52840 with DFU (usb-serial). On windows I can use nrfutil. But how to proceed if I want to do that from another microcontroller?
Is...
Hi,
I am working with nrf52840 DK and sending real time sensor data to nrf toolbox using ble_uart. I would like to store adc output in flash and then send it over ble uart...
Hi Devzone
I tried to use saadc with 4channels. when I use this without fpu_fft, It prints correct value well.
But, when I insert the fpu_fft and run it, after a while...
Hello
I have a question about SIG certification. As far as I know, to get SIG certified, I need to download the DTM firmware to the board and pass it to the certification...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Dear Community;
I am trying to make an HTTP GET request based on this code . It works fine but I need to adapt that to fit it in my code. I need to pass some arguments...
Hello!
Is there a way to send gps nmea data through ble connection? Almost all gps bluetooth devices use bluetooth classic to send data. The mobile app where I need to get...
Hi,
I need to read the data from the sensor MAXCESS Digital load cell amplifier in which the output we are getting in the form of current ( 4 to 8 mamp) not voltage. can...
Hey guys,
I've been troubled by the this 0x3E issue for almost disappointed to Nordic.
I'm working on a CENTRAL,which is going to connect a headphone with to read some...
Hi i am checking for the Rssi value of the low power node,when i am placing the device in certain feet, it is giving the rssi reading which is approximately matches with others...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
As per below mail I changed settings for...
Dear all,
I'm using an nRF51822 chip for implementing a BLE HID device (mouse) (SDK ver. 12.3.0, SD ver. s130_2.0.1)
I have problems when connecting via BLE with laptops...
