hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
Dear nRF52832 experts,
I have a SPI slave device which can periodically notify the MCU with data ready (DRDY) signal. For each DRDY signal, we should perform a SPI transaction...
Hi there, I am developing a mobile solution using BLE. Actually I use a sniffer based in IC nRF51822 and Wireshark + nrf sniffer as a tool for traffic capture. Sometimes,...
Hi,
I have similar problem to what is described here .
My situation: 1. I connect 2 PDM mics to the board (CLK is pin 27, Din is pin 26). 2. I connect a couple of TWI...
I was wondering if there is any way to setup a callback when data is received on an open socket, as opposed to just regularly polling the socket?
The application I have...
Assume a BLE connection has been established between a master and slave. The device in question could be either the master or the slave (if it matters).
I have an application...
Hi, when using fds_record_iterate() to iterate over records, it only returns the record ID, but not file ID or record key. Only after opening the record you get the file id...
The nRF52810 datasheet shows the EVENTS_COMPARE register as RW, so I'm assuming that I can write to it.
But when I write to it, nothing happens.
Example.
I set up...
The question in short form is, is there any way to not use the Flash for storing bonding information and instead do this in RAM?
For the longer explanation:
We are using...
Hi,
We've circled back to this problem, now that we've increased speed.
We're using UART to communicate between the nRF52832 and an STM32.
Recently we increased the...
Hi,
I am trying to read UART data which is populated from another device going into the nordic board.
However, I am unable to read this data. I am using the ble_app_beacon...
Hi,
We are running a setup that pumps sensor data from light switch server to light switch client. After provisioning/configuration the setup is working fine without any...
