Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
I study on Thread resently.
I found it is not any output in the Debug Terminal Window when using NRF_LOG_XXX, but the J-link Control panel showed the logs.
Here...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
Dear nRF52832 experts,
I have a SPI slave device which can periodically notify the MCU with data ready (DRDY) signal. For each DRDY signal, we should perform a SPI transaction...
Hi there, I am developing a mobile solution using BLE. Actually I use a sniffer based in IC nRF51822 and Wireshark + nrf sniffer as a tool for traffic capture. Sometimes,...
Hi,
I have similar problem to what is described here .
My situation: 1. I connect 2 PDM mics to the board (CLK is pin 27, Din is pin 26). 2. I connect a couple of TWI...
I was wondering if there is any way to setup a callback when data is received on an open socket, as opposed to just regularly polling the socket?
The application I have...
Assume a BLE connection has been established between a master and slave. The device in question could be either the master or the slave (if it matters).
I have an application...
Hi, when using fds_record_iterate() to iterate over records, it only returns the record ID, but not file ID or record key. Only after opening the record you get the file id...
The nRF52810 datasheet shows the EVENTS_COMPARE register as RW, so I'm assuming that I can write to it.
But when I write to it, nothing happens.
Example.
I set up...
The question in short form is, is there any way to not use the Flash for storing bonding information and instead do this in RAM?
For the longer explanation:
We are using...
Hi,
We've circled back to this problem, now that we've increased speed.
We're using UART to communicate between the nRF52832 and an STM32.
Recently we increased the...
Hi,
I am trying to read UART data which is populated from another device going into the nordic board.
However, I am unable to read this data. I am using the ble_app_beacon...
