Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I'm trying to simplify the open_bootloader example from SDK 15.3. I'm getting rid of version, signature and keep only the CRC validation. I'm actually trying to understand...
Device: NRF52832_xxAA Softdevice: S113 v7.0.0
Hello.
Sometimes, during firmware running, I get a fault from Softdevice with pc: 0x0001A990. Could you inform me what causes...
When I send 90 KB data via BLE. Sometime I am getting NRF_ERROR_RESOURCES error. I have tried all the things that are available in support site. I am reading data from SPI...
Hello Forum,
I got a Thingy:91 today and of course I wanted to test it immediatelly), but I wonder:
Is the nrfcloud.message simply because of no LTE-NB1 network / roaming...
We are migrating BLE application code from SDK-12.3 to SDK-15.3.
Our firmware uses SPIS module. Now in the example code I could see
NRF_POWER->TASKS_CONSTLAT = 1;
What...
setup:
segger V4.20a
windows 10 pro
SDK: nRF5 SDK for MESH 3.2.0
hardware;
NRF52840
I am trying to implement the simple_on_off model instead of the regulat...
Hello! Just started looking in to using whitelists and looking for information in the infocenter but the "advertisement module" is inaccessible on NRF SDK v15.0.0/libraries...
I'm working on a solution that will need to acquire GPS location and backhaul that to the cloud over LTE. I'm trying to figure out whether it makes more sense to go into PSM...
Hello All,
I am measuring the nRF9160 current in the sleep mode(program with just k_cpu_idle(); command) but still I am getting 530uA current. I have also tried to change...
Hi,
We are using ncs 1.0.0 and modem fw version 1.0.1.
We are currently using 2 UART, 1 SPI and 1 I2C peripheral in our application.
We want to use one more UART in...
I merge all hex file of Bootloader, Bootloader Settings, SoftDevice and Application with Buttonless DFU code included into one hex file. After that, i recover the device....
Hello Nordic team,
I am trying to get my product read for FCC/CE compliance testing. I came across the radio_test example and other examples posted on DevZone. I have the...
Hi,
I have just recently started to develop an NRF52832 chip with Keil uVision 5.
My setup is the following:
PCA10028 Development kit connected to Feather NRF52832 bluefruit...
Hi,
We are planning to add an external flash to our nrf52840 based design.
The flash type is
http://www.puyasemi.com/uploadfiles/2019/06/20190604154800480.pdf
I'd...
