Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
Sorry for the many tickets the past few days, but I am ramping up to start a nRF Connect SDK project on a nRF91 modem and have encountered some initial growing pains...
I am unable to debug a Fanstel BM840 nRF52840 based simple custom board using a nRF52840 DK. I believe the custom board is basically ok: Before flashing my application onto...
Hello,
I'd like to ask if or how is possible to set Thingy:91X as a Wi-Fi STA or AP? I found some examples for Wi-Fi but Thingy:91X wasn't in device list to choose. Could...
We have been evaluating the nRF5340 and nRF7002 for use in a new product and we are currently looking at our Wi-Fi FOTA options. For reference, we are using an nRF7002 DK...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hello, I have been observing some interesting behavior concerning packets sent from server during eDRX idle period. When the period is set to 20.48s or 40.96s, any packet...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
I am using two nRF5340 Audio DKs one as a gateway and the other as a headset. I tested the nrf5340_audio example and managed to get the speaker output working through the...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic,
I want to implement a LED blinking like below pseudo code. I'd like to use PWM sequence Timer x n , GPIOTE, PPI since it doesn't consume any CPU time. for ...
The functions “ nrf_log_frontend_std_...() ” called by “ NRF_LOG_INTERNAL_MODULE(...) ” use only 4-byte (uint32_t) arguments, which is not suitable for arguments of type ...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
