We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
I have trouble programming the PDK using nrfjprog. I can flash the program fine using Segger Embedded Studio but it doesn't appear to be working using nrfjprog.
Here are...
When using ble_app_uart, I set the advertising timeout to 10s, but after the timeout did not enter sleep, but automatically reset,my judgment is based on the terminal to send...
Hi
I have run this example code
nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject
when I operate...
I want to reprogram a nRF51822 xxAC device on a existing product.
I have a J-Link (SEGGER) device with latest firmware.
I'm running the SEGGER J-Flash V6.20e utility.
I...
Hello,
I have constructed a custom board with nRF52832 and MPU9250 on it.
I have flashed the program for reading battery service, temperature service and MPU9250 readings...
I followed the tutorial on devzone.nordicsemi.com/.../ to use Eclipse, GCC and GNU Debugger.
I encountered an error after the successful build (with key symbol) with CDT...
Hello,
I purchased nrf51822 module and i want to use s130 sdk for my project.
But when i have look over using keil i found that it requires jlink debugger or jtag debugger...
I am studying about developing a simple BLE 6LoWPAN network. My proposed topology is mentioned below:
internet - - - - - - - - - BLE1 - - - - - - - - - BLE2
| \
...
Hello,
As we can see, the mesh stack is a totally new stack which is independent of traditional BLE stack. Could you please explain why to design like this?
I found there...
Hi, I'm deeply interested about the Nordic's PCA20014; a.k.a solar beacon .
This HW uses
Amorton AM-1417CA solar cell, 1.5V, 12.5uA at FL-200lux
2 channel...
Hi,
I have run into a problem with the nRF sniffer. I used it in late May and early June to debug a BLE connection between a nRF-DK and a HTC Desire 610 and it worked fine...
Hello,
I am trying to communicate urart with nrf52840 and other devices.
But there was a problem.
You can transfer data from the nrf52840 to another device, but if...
Hello,
I need to connect an event handler (i.e. a function) to two NRF_RADIO events:
-NRF_RADIO->EVENTS_ADDRESS
-NRF_RADIO->EVENTS_READY
I know I should use the NRF_RADIO...
Hello ,
I can read the rssi value after the connection is established.
case BLE_GAP_EVT_CONNECTED:
APPL_LOG("Connected to target\r\n");
err_code = bsp_indication_set...
On this question it is said:
"Error code 0x3201 means BLE_ERROR_GAP_DISCOVERABLE_WITH_WHITELIST: Use of Whitelist not permitted with discoverable advertising ."
Why does...
