I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hey all,
I'm working with the nRF51822 (nRF51dk) on a mac running high sierra, and I've been following this tutorial to try to get started. But when I try to make flash...
Dear Nordic engineer,
I try to setup Wireshark sniffer with nRF52-DK. I followed by nRF sniffer user guide v2.0.
I see interface toolbar of nRF sniffer on Wireshark. But...
Is there a block header information available that I can read thru the flash read function (e.g. in ble_flash driver, ble_flash_page_read() function ) ?
My FS (file system...
Hello,
I would like to understand the reason behind getting a error,(0x04) NRF_ERROR_NO_MEM , when calling the function
sd_ble_gatts_characteristic_add(p_service->service_handle...
I'am realy new to nRF52 development. I want to start with a simple demo as shown on www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit.
What HW do I...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
Is there a nordic guide which lists out the steps taken by the chip when going though a bonding process? I am trying to add as many RTT printouts as possible to know where...
finally I have done to implement that ADXL345 can throw data over BLE using nRF UART app service with this code . now my problem is how to change 2's complement ADXL345 data...
Hi,
We are using a nrf52832 in a serialized application with a STM32F4 and standard SPI as the transport layer. We are using the SDK V12 on the STM32 and softdevice S132...
Hello,
I want to add DFU fonction on my custom application. The final goal is to update my firmware from my custom app (not just once).
My setup is : SDK11 - nRF52832...
Hello All,
I am using the HRS example as reference from Nordic SDK14.1.
I have one central and 4 peripheral devices.
I have the MAC ID's for all the four peripherals...
Hello Nordic Experts,
I have One central device and and 4 peripheral devices.
At this point of time I am trying HRS example on it, the example is running fine with single...
Hi everyone,
We are trying to choose which protocol use for connecting devices based on Nordic SoCs.
We use devices in following way:
about 300 - 500 devices (wearable...
Hi there,
The dfu secure bootloader example is working fine with my nrf52832 sdk14.2 s132. but the experimental buttonless dfu in the example is not working for me. I was...
Hello,
I have nrf51 beacon that is protected from read. I want to recover it (erase and disable protection) but I only have st-link programmer. How can I do that? Maybe...
