Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi Guys, I try to implements the ctrl-C/V for bluetooth HID keyboard. But from SDK, I can't figure out how to send two keys. Even I do not use buffer_enqueue/dequeue in order...
Hello,
I try to build mesh sdk for nrf52840 it gives me error on RTT
0> <t: 0>, main.c, 318, ----- BLE Mesh Light Control Client Demo -----
0> <t: 0>, main.c, 108, Initializing...
hi, In my setup, I have a 3.7 V battery divided down to the bandgap range using a 100k and 100k resistors, so the voltage at the ADC input is 3.7 * (100/200) = 1.85 V. I am...
Hi
I used "nRF5_SDK_for_Thread_v0.10.0 - cli sample code and try to test Thread command "diag"
when I type "diag" then it will show "diagnostics mode is disable".
...
I am working on a project which involves sending data from many beacons to many other beacons. To be more specific, I have two groups of beacons:
The first group consists...
I'm planning to use one of those beacon platforms:
www.ebay.com/.../352167746226
www.ebay.com/.../112493464451
for a close proximity positioning system now I'd like...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Building for a PCA10040 dev board (nrf52832) in SDK 14.0.0 with the S132SD v5.0.0
I'm an encountering an issue where calls to printf() are only displaying a single byte...
Most application examples which use the scheduler have a main loop looking something like this,
int main(void)
{
// Initialization <snipped>
// Enter main loop...
Hi,
"wait" hangs when running the mbed blinky example, build in develop or release, on nrf52840.
The program is flashed with a J-Link and the program runs OK at first...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 1 cannot...
We have ordered nRF52840 development kit . In windows xp comp port is coming as 8 but the device status in general is this evice cannot start.(code 10). Same in windows 7...
Hi,
I am working on ble_app_uart_c central code provided in sdk12.3.0 with softdevice s130.I added pwm code provided in peripheral examples in ble_app_uart_c central code...
