Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi,
I am evaluating nrf52840 using the light switch example.
Environment:
Soft device : s132_nrf52_6.1.1
Mesh SDK Version: 3.2.0
SDK Version: 15.3.0
IDE: SES ...
Hello!
I currently want to save the sensor data obtained by SPI communication to the microSDHC card by SPI communication.
Writing to the SDHC card is possible without...
To the kind attention of Nordic support team,
I'd like to open a new thread after the first one ( https://devzone.nordicsemi.com/f/nordic-q-a/46318/configuration-of-gzp_dynamic_pairing...
I have been using Power Profiler Kit nRF6707 for awhile without problem.I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on the...
Hi all
The iC is not advertising , neither it is able to get programmed.
The voltage levels are ok. It is getting sufficient Voltage at its o/p and delivering o/p at DEC...
Hi,
Please help to share Memory size of following SoftDevices:
S112
S113
S132
S140
Also, what will be the memory size of SoftDevice if i implement Central +...
Hi,
We are migrating from 12.3 SDK version to 15.3 version.
We observed the almost 22 KB of RAM is reserved. Where as in 12.3SD version we don't see this.
We are still...
Hi,
our company one new product using you nRF52832. We already prepared everything for CE (RED ) and FCC certification process. Only thing that is unclear is Bluetooth SIG...
Hi!
I am currently using SEGGER Embedded Studio version 4.12, nRF5 SDK version 15.2.0, nRF5 SDK for Mesh version 3.1.0, Hardware BMD-300 Evaluation Board.
i using the...
I need to measure a load-cell bridge. Although, I'm fairly certain I'd be better off with an external delta-sigma ADC with an internal amplifier - I'd like to run through...
Hi,
I study on Thread resently.
I found it is not any output in the Debug Terminal Window when using NRF_LOG_XXX, but the J-link Control panel showed the logs.
Here...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
