hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
OS: Ubuntu
IDE: SES
Our application is has a notify characteristic that works when attached to the JLink debugger. I can get...
Hi, I am using nRF51822 on my custom board with SDK 12.2.0. I use DFU bootloader, and can update application in BLE from DFU mode with bootloader (dual bank mode is used)...
I am using the nrf52 Dk with nrf52832 chip and i want to write bulk data onto the dk and then when i read the dk from the mobile app nrf connect, i want to see the written...
Hi,
I am trying to integrate the DFU service into the ble_app_uart example. I am using NRF51822 with SDK 11. I was able to successfully run the ble_app_hrs with dfu. So...
Hi. I'm using 2x nRF52840 DK's + eero pro.
I've been noticing some stability/longevity issues with examples/thread/freertos_coap_server in nRF5SDKforThreadandZigbeev3209fade31...
Peer Manager in recent SDKs supports up to 20 peers but SoftDevice functions like sd_ble_gap_whitelist_set() and sd_ble_gap_device_identities_set() are able to handle up to...
Hi, I am trying to get BLE packages with the nRF52840 Development Kit without using Wireshark or other external app. Does anyone have any solution? Thanks in advance
I have followed this tutorial from this link but cannot get it work.
I have 3 loop. For the first loop of sending data it will have a delay about 1s and until 2 finish...
A%dBBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX = 40bytes
1) In Termite:
Data is complete and in sequence when until 6 only.
A0BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...
I have 2 message order by sequence and between each of them have delay 2s. for Example
How should it work
A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX
Delay 2s
A2BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...
Hello Nordic Support.
it was first time i tried to set up zigbee project based on 52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. and now i got question...
...
Hello,
I want to design my board using Raytac MDBT42Q-AT-UART module which has nRF52810 QFN SoC inside.
I need BOM with P/N and make of components which are used in...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) I want to configure Advertisement channels...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
Most of our devices are Peripherals. To control them, we will relay...
