Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
When the bluetooth service function is initialized, sd_ble_uuid_vs_add() is called in the ble_dfu_buttonless_init() function in case of an out of memory error. In the ble_nus_init...
Hello, Is there any evaluation kit available for NRF905? I found this one online but DIGIKEY website says its obsolete::
media.digikey.com/.../nRF905-EVKIT_PS_Rev1.0_Jan2004...
Dear Nordic staff and users,
Now I'm trying to confirm that my local LTE operator supports energy saving modes. It went with flying colours with PSM:
at+cereg=5 OK at...
using SEGGER Embedded Studio for ARM V4.30a, I get a problem of Linking with an nRF5_SDK "blinky" examples. See hereunder the error message:
Seem to be a problem of configuration...
Hello,
I can create a zip file with nrfutil pkg generate and there is a bin file in it? I want to make DFU as a bin file only.
I only want to download the firmware as...
Hello,
I have a question about using pins as output. I'm trying to set 2 pins to "1", but cant fully understand how to use pins on port1.
for example: P0.10 (wich works...
Hallo,
I want to use the UARTE instead of the UART to transmit some audio data to DK. The Basic Project is the i2s example in nRF5_SDK_15.3.0_59ac345.
I implemented the...
I'm starting initial development on a new project using the nRF52832. I've been able to transmit successfully using nrf_serial_write but nrf_serial_read always returns NRF_ERROR_INVALID_STATE...
I'm working on a BLE central based on the Nordic UART Central example. The peripheral I'm talking to has a characteristic that sends an indication when written to. I'm writing...
Hello Nordic Community,
I found bsd Irrecoverable error on my other ticket
https://devzone.nordicsemi.com/f/nordic-q-a/53913/support-on-nrf9160-irrecoverable-3
I just...
Hello,
I've got a nrf52840 DK and Adafruit nrf52840 Express (less complicated then DK) i'm trying to run a PWM example from datasheet (46 PWM — Pulse width modulation...
