Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I'm working on an ESL project using the nRF5340-DK. I need to enable the PAwR feature, which requires Bluetooth 5.4. However, my current program is written using nRF Connect...
I've created a custom board (trying to expand on the things I learned from the Intermediate tutorial). If I had on my `Kconfig.defconfig` the following:
I get: Also on...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hello Nordic Support,
I am developing a bare-metal, non-secure firmware for nRF9160 using nrf_modem from SDK nrfxlib v2.9.0 , without Zephyr or RTOS.
I followed the porting...
I am having issues programming my nrf5340dk through VSCode or the nrfjprog tools. I have tried as many remedies I can find on the DevZone but not of them seem to correct my...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I am using:
NCS 3.0.1 nRF52840DK
My project is based on the coap_client sample, currently running on a nRF52840DK. I have modified it to add the 'observe' option in the...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
I'm planning to build a project using the Nordic Thingy:91X. My goal is to collect sensor data (e.g., environmental or motion sensors) from the device and transmit it over...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
