Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
This question is similar to this thread:
devzone.nordicsemi.com/.../
However it was framed differently and didn't really clear anything up for me.
Say my application...
Hello,
I have an application that has to be ported to the newer Softdevice version. I've already ported my application to the SDK 13 and tested it with the new Softdevice...
The NVMC documentation states the CPU is halted while the NVMC is writing or erasing flash. If the CPU is halted, then interrupts shouldn't need to be disabled during flash...
blog.bluetooth.com/management-of-devices-bluetooth-mesh-network
The Provisioning Protocol
During provisioning, the Provisioner and the Device to be provisioned communicate...
as this screenshots show, i add some headers to nRF_Libraries, and add the directory of the folder nRF_Libraries to Options for targets /c++/include paths,but after building...
Hi,
I am trying to use the SAADC via ble when noridc is connecting with other device and adding value to advartasing. This is my code but i've got some problems.
1)...
I am modifying the bootloader_secure_ble code to receive a serial number via BLE and store it in flash. However, whenever I call nrf_dfu_flash_store or nrf_dfu_flash_erase...
Hi,
We are currently working on one project.
Initially, the nRF52840 & S140 (v5.0.0-2) & SDK14.0
examples \ ble_central \ ble_app_multilink_central Based on the example...
Hi Team,
I am using sdk12.2.2 and nrf52. I want to use one gpio to detect button state & have to operation on that event.
I used one method to configure(code snippet...
Following the guide found at : file:///C:/Github/STIWHN/SDK_thingy52/thingy_sdk_v2.1.0/documentation/firmware_compile.html#compile_gcc
I still getting errors trying to...
Hello,
For the softdevice update, is it the responsibility of the bootloader to make sure, that the softdevice was copied correctly?
If for example the bootloader calls...
Hi,
When i use FreeRTOS tasks with priorities 2,3,4,5 what i need to #define for XXX_CONFIG_IRQ_PRIORITY of SPI,SAADC and GPIOTE at the file sdk_config.h
Thanks
Hello, I use nrf51822 , sdk 8.0.0, s110
I defined advertise interval and timeout
#define APP_ADV_INTERVAL 320
#define APP_ADV_TIMEOUT_IN_SECONDS 3
Also, I write...
Hey Nordic Devzone,
I am really new to Nordic and am still a student in embedded software engineering. So first some background information.
I have 6x nRF52840 and 5x...
Hello,
I am designing a custom 2layered PCB board with NRF52832 IC. I have followed the reference design given in IC's datasheet as shown in the figure. Please provide the...
