Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello,
I want to add NUS service on the SDK_14.1.0_1 example called "ble_app_hrs_rscs_relay".
I added
uint32_t nus_err_code;
ble_nus_init_t nus_init;
memset(&nus_init...
Here: devzone.nordicsemi.com/.../group__ble__api.html
Choose to simply not keep track of available buffers at all, and instead handle the BLE_ERROR_NO_TX_BUFFERS error...
We plan on using 4 to 5 timers on our project. Each timer has different timer intervals (Example 1 minute, 50 ms, 300 ms etc)
We are trying to use 2 Timer instances and...
Hello,
I am working on example
nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c
pca10040\s132\arm5_no_packs/ble_app_uart_c_pca10040_s132...
Hello, I would like to know if there is any way to avoid bootloader start in secureDFU firmware transfer. All the checks on init file and control point are on the application...
My DFU is staying in the bootloader, even after successful download of the application package.
I have modified the secure bootloader for my custom PCB (removed the GPIO...
Hi,
I'm trying to get OpenOCD flashing to work on Windows using the FTDI 2232H adapter and an NRF52 target. I found this site:
https://www.allaboutcircuits.com/technical...
Hello,
I am trying to read multiple registers from a slave of i2c.
The values that I capture are the first value repeated in all the buffer.
The number of readed reg...
Hi,
I would like to use ping pong mechanism to prevent faulty application update on nRF52840. Is there a way to build a single image to run at 2 different addresses? How...
I have OSX Sierra, VMWare Fusion and Windows 7 available.
I do Arduino (Teensy) dev, staying on the OSX side.
I want to use the nrf52 chip as a MIDI over BLE conduit ...
Hello,
I have a PCB with a NRF52 powered by batteries. We need to be able to plug the batteries, then program the device and never remove the batteries.
We noticed, that...
I have a need for an interrupt to go off at a 4khz rate. For this, I am using a repeated App Timer (running off the 32k crystal).
Prior to adding this extra timer, we used...
