After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello!
We are performing certification testing for our product. We have nRF52832 chip on the board. We used "radio test" example to perform the test and almost all worked...
I'm migrating from sdk13 to sdk14 with work app.
Can't solve one weird problem. When my app start first time I initialize some data with saving by fds library to flash. There...
Hi
I get the following error when i compiled the ssd1306 library from link text to my nrf51DK..
error is: ._build\nrf51422_xxac.axf: Error: L6200E: Symbol app_error_handler...
In the nRF52 datasheets there is a statement:
"The 64 MHz crystal oscillator (HFXO) is controlled by a 32 MHz external crystal"
Is the crystal somehow oscillating at 2nd...
I am trying to compile the blinky example in the SDK 14.
I am getting this error:
makefile:111: ../../../../../../components/toolchain/gcc/Makefile.common: No such file...
I need an application that always advertise the beacon information, such as RSSI and Major and Minor value. At the same time I would like to transmit HID keyboard code. Is...
Hi
I have an application where I cannot use the FIFO buffers (HW or SW). Therefore I need an interrupt for each received byte. If I try to use the uart driver (nrf_drv_uart...
I'm trying to program my nrf52832 with an ST-LINK /V2. I can't get both the softdevice and my app on the chip.
Flashing each one seperately works fine but then when I flash...
Hello there,
I'm trying to flash my custom nrf52832 pcbs(untill I get my DKs in the tech tour with a reconfigured stm32 disco board's SWD port with keil uVision using the...
Hello.
This is my code to "wait until micro sd card is pluged".
while(1)
{
disk_state =disk_initialize(0);
if(disk_state==RES_OK)
{
NRF_LOG_INFO("Initialize...
Hello community,
I have a central device which I implemeted, it is running with SD 132 v 4 ("NRF_SD_BLE_API_VERSION=4")
) the chip is a NRF52832, I have some movement...
I have no idea how i can install this and use it.
I would like if any one can explain in detail.
Can you get picture how I can do it?
I am using ble_app_hrs_nfc_pairing...
Hi,
As of now i am using nRF52840 and SDK 14.0.0 and i can find only BLE examples and i wanted to work on bluetooth 5 where can i find examples?.
And i want IR generator...
Hi ,
I am not sure if it is the right place. I was looking for WiFi: 802.11 b/g/n 2.4 GHz support in Arduino UNO and stumble into Arduino primo, which is developed in cooperation...
