But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am using NRF52 SDK14.0 and SoftDevice S132 v5.0.0. Application freezes somewhere in SoftDevice if sd_softdevice_enable() is called after nrf_drv_clock_lfclk_request() was...
Hello All,
Where would I find a library file for a PID controller? Forgive me if there is an obvious answer. I'm new to working with Keil.
Thanks for taking the time...
We need to put the processor in sleep mode (to conserve battery power) and wake-up the processor when the user touches the Cap Sensor pad.
Can you Cap Sensor in nrf52 be...
I'm using "nrf5_SDK_for_Mesh_v0.9.2-Alpha". And, I build examples using "SEGGER Embedded Studio 3.26a".
Now I want to modify examples for my custom board.
In CMake, "...
Hi, a little background information first, when debugging ble mesh example 0.9.x:
devzone.nordicsemi.com/.../
I'm now kinda having a massive problem with this function...
Hi,all.
I am using nRF52832.
Does the nRF52832 support dual mode that allows simultaneous advertising and scanning?
Are there any examples you can refer to if you...
Hi I use SDK 12.3 and sdk 2.0.1 , and set a device name length is 21 like "1234567890ABCDEFGHIJK" by sd_ble_gap_device_name_set;
but in the advertise data the name length...
Hi,
we are developing and application on iOS which can among others, update our hardware over the air, and we found out that e.g. after bootloader update is done, then...
Our hardware has an externa memory connected to the nRF51 by SPI, we also use DFU to update the firmware creating the zip pack (We have buttonless dfu working as well) and...
I've been using the nRF52832 chip for over a year and it works great. However, for a new project I designed a board so that the nRF52 chip was the slave on a SPI bus, and...
Hi,
I just try DFU function in sd130/sdk12.3 and it does work very well.
I did:
(1).Generating your own key:
nrfutil.exe keys generate priv.pem
(2).Display a public...
In the example code, I found this:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
I'm having 2 boards (maybe extremely problematic) and I want to...
I have seen at least one person here who has gotten Nordic's UART-over-BLE example app running on the nRF8001. How was that done? Where is it? This example app is not included...
Screenshot of what I'm doing:
So I reset the nRF8001, then try to initiate a transfer by pulling REQN low. However, nRF8001 never responds by pulling RDYN low. I have...
