But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I've recently introduced the Stack Guard and App Timer 2 libraries and noticed a couple <info> logs popping up in m RTT console despite logging for those two modules being...
Hi Nordic Team,
In my BLE project when I was trying to add Device information Service(GATT) in BLE central multilink example code, once the connection between central and...
Hi,
I am trying to modify the code in the BLE_App_Buttonless_DFU_pca10040_s132 example is SES. Without any modification the code compiles fine and can be recognized by nRF...
My issue like this ticket
https://devzone.nordicsemi.com/f/nordic-q-a/39428/usb-msc-corruption
I suspect it is caused by a problem in the implementation of the NRF_BLOCK_DEV_QSPI_FLAG_CACHE_WRITEBACK...
Hi,
We encountered a problem when added new models through an OTA DFU. Specifically we upgraded a device with SoftDevice 6.1.0, SDK 15.2 and Mesh SDK 3.1.0 to SoftDevice...
Is it enough just to connect from custom board to P20 header(nrf52840-dk) SWDIO, SWCLK, RESET, from custom board GND to P20( GND_DETECT) and power supply to custom board from...
I need to enable UART1 in runtime in order to be able to read some data coming on that device.
In order to be able to use the uart functionality, I need to set CONFIG_SERIAL...
Hi,
As the subject description, I just remove the part of hid function from main.c then make the personal source file.
Before I removed, the project could work as usual...
Dear Nordic
there are two question find in my software. it may be some matter with thest two question, so put here together.
1.
My software will be reset about several...
for the i2c_3 to work the following is needed to modify the SDK.
nrf/subsys/spm/Kconfig
```
config SPM_NRF_TWIM3_NS
bool "TWIM3 is Non-Secure"
default y
```
...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
