Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I have a strange bug, that I do not have any good answer for.
In the software, I use either SPI1 or SPIS depending on current configuration, I have seen some rare cases...
I know it's not very common to use a secondary service, but I want to use it in one specific scenario. When referring to the documentation for the API sd_ble_gatts_include_add...
Hi,
I'm trying to use the LPCOMP of the nrf52 telit board.Configured lpcomp with the following settings :
Input : AIN2
Ref : AIN1 ( external ref. of 1.6V)
Detection...
Hello I am using PCA10040, nRF52832, and GCC toolchain
I have a project that was working good using sdk v12.3 but now I want to migrate to the latest and I am getting one...
Hi
After the device has been in idling, the sleep_mode_enter function is called which then calls
sd_power_system_off().
The device then goes into sleep mode until a...
Hi! I need your help!
I need to create some mesh network consists of simple devices (A) which could collect mac addresses of all visible Bluetooth devices (C) and send it...
Hi, I try to mount some I2C devices at Arduino Primo but I can not get any results. I tried an I2C LCD that did not return any error but did not display any text. When I scan...
Hi,
I am using IAR for the pca10056 with a nrf52840 chip. Can I change the compiler in IAR? I simply just downloaded the newest version from the IAR homepage and specified...
Hi I'm trying to compile the experimental_ant_bootloader for the pca10040 with a S212 soft device using the armgcc compiler using SDK13
I can't find a makefile or linker...
How do you do
1.In the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral here, there are three PWM routines:
Low_power_pwm, pwm_driver, pwm_library but only...
Hi, there~~. The PCA20006, nRF51822 Bluetooth Smart Beacon Kit, is fascinating!
So I'm planning to create a custom beacon product of my own,
a 2-layered PCB with nRF52832...
I have trouble programming the PDK using nrfjprog. I can flash the program fine using Segger Embedded Studio but it doesn't appear to be working using nrfjprog.
Here are...
When using ble_app_uart, I set the advertising timeout to 10s, but after the timeout did not enter sleep, but automatically reset,my judgment is based on the terminal to send...
Hi
I have run this example code
nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject
when I operate...
I want to reprogram a nRF51822 xxAC device on a existing product.
I have a J-Link (SEGGER) device with latest firmware.
I'm running the SEGGER J-Flash V6.20e utility.
I...
