This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I did some power measurement on the nrf52 DK with the Nordic profiler kit and the result was way more than what we could expect from a nrf52 (about 1 mA). Even in...
I am working on the ANT connectivity for a product we've developed, called RunScribe [a shoe-worn running sensor], and am seeing some issues on Fenix 5 watches with our ANT...
Hi,
I'm trying to implement run the ESB and the BLE concurently using the timeslot API.
I started from this example : devzone.nordicsemi.com/.../
The problem is this example...
Hi,
I'm quite a beginner to this whole nrf52832 world and I'm trying to read some data from a flex sensor wired in series with another resistor connected to VCC now I understand...
In brief our problem with rfx2411n is that rfx begins to draw 200ma current without any reason. Rfx is powered down, powered from 3,0v. And suddenly something happens and...
I have a device that runs with nRF51 chip with the NRF UART Service (NUS).
I have a Raspberry Pi 3 and I want them to communicate.
The device requires an authentication...
My question is related to peripheral device only. I have implemented an auto connection interval negotiation algorithm which works as expected and negotiates connection interval...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
i have nrf52 dk i run simple examle saadc from sdk 12.1.
now i want to get result.
i can't understand the code.
i start putty terminal adc event number and app info number...
I'm having trouble adjusting ram start setting using the new SES projects from latest SDK14.1.0
I have tried the project linker section placement macros settings of
...
