When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello Team,
I just recently purchased Thingy52 i was wondering i can use NFC NDEF update using python library if it is possible can you point me to right
documentation...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi，
Recently，i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west，then run command “west update”，but got an error：
Can...
Hi ... folks
I am using nRF52832 and analog IR sensor , Working with the example saadc . In this case , i am giving the IR sensor input voltage as 5v , analog pin 2 .I am...
Hi,
I am using NRF52832 Development board, SDK(nRF5_SDK_15.3.0_59ac345) from this i am using (/nRF5_SDK_15.3.0_59ac345 (4)/examples/ble_peripheral/ble_app_uart) example...
Is the nRF52 RSSI block of the RADIO module based on the entire 2.4GHz ISM band, or can it be configured to only measure a given 1-2MHz band of interest? According to the...
I'm using the serial library for the first time. What are the advantages/disadvantages of using IRQ and DMA? How should FIFO queue and buffer sizes be chosen?
Hi,
I am using the following code to implement a millisecond timer read function. In main, while loop, I do nothing but run a 1ms delay and measure the time in mill second...
Hello, I'm a researcher.
I wanna use Bluetooth CTE(Constant Tone Extension) feature with 1-antenna TX + 1-antenna RX.
I have seen some articles that nRF52840 DK does...
I am using nRF52832 with SDK 16.0.0. I have a simple application that uses SAADC and BLE. It reads values from three channels AIN0, AIN2 and AIN4 and sends them via BLE every...
hi all,
we're developping an application to control the frequency and the duty cycle of a pwm signal throuth ble .
firstly we have built both the functionalities separatly...
