When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am using nRF52 DK kit which has SWD connector for booting External device but it is booting only nRF52 Board not the external board
please can any one suggest me the right...
Hello,
I am designing a custom PCB with NRF52832 IC. According to datsheet, required specification of inductor L1 are:3.9nH, 0402 package, 5% and a High-frequecy chip inductor...
Hello,
I did some power measurement on the nrf52 DK with the Nordic profiler kit and the result was way more than what we could expect from a nrf52 (about 1 mA). Even in...
I am working on the ANT connectivity for a product we've developed, called RunScribe [a shoe-worn running sensor], and am seeing some issues on Fenix 5 watches with our ANT...
Hi,
I'm trying to implement run the ESB and the BLE concurently using the timeslot API.
I started from this example : devzone.nordicsemi.com/.../
The problem is this example...
Hi,
I'm quite a beginner to this whole nrf52832 world and I'm trying to read some data from a flex sensor wired in series with another resistor connected to VCC now I understand...
In brief our problem with rfx2411n is that rfx begins to draw 200ma current without any reason. Rfx is powered down, powered from 3,0v. And suddenly something happens and...
I have a device that runs with nRF51 chip with the NRF UART Service (NUS).
I have a Raspberry Pi 3 and I want them to communicate.
The device requires an authentication...
My question is related to peripheral device only. I have implemented an auto connection interval negotiation algorithm which works as expected and negotiates connection interval...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
