Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello,
I would like to make use of white list advertisment for my heart rate application on my nrf52832 s132 pca10040, currently I am using SDK12.2, is there some example...
Hello,
I used translation software.
I'm looking into LDO mode and DC-DC mode.
However, I did not know what LDO mode and DC-DC mode are.
What are LDO mode and DC...
I'm working on a project that will utilize the nRF52832 as the Host and Controller and an STM32F3 as the application using serialization.
I've included the nRF5 SDK V14...
We just produced a PCB with a NRF51822-QFAB-R7, does Nordic provide a EMC test firmware that we can flash onto the chip? Basically need it be always transmitting....
Thanks...
I'm using the original BLE App UART from nRF5_SDK_14.0.0 on a PCA10056 Board.
The board is advertising, but if I want to open a BLE peer-to-peer connection, than the application...
With SDK 14.0.0 and Softdevice 5.0.0 I have problem with Windows 10 connection. The device connects to PC but then almost immediately disconnects with reason 0x13 (BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Hello,
We developed a few devices using the nRF51822 and noticed that the receiving range is reduced significantly from our nRF24L01 devices. The transmission range is good...
Hello,
I'm trying to measure the current profile with the PPK (HW Rev:1.1.0, SW: 1.1.0) but I see a lot of strange behaviors.
My firmware initializes everything and the...
I am running a nrf52840 dev board as an NCP connected to a RASPBERRY Pi running wpantund.
I have 10 other nrf52840 devices in the network. The PI has LIBCOAP coap-client...
Hi,
Just curious to know if anyone else had this issue and how they solved it.
My colleagues and I are working on code based on the Nordic Uart Service, in SDK13.1.0...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I am using 3 uarts for my applications using nrf52xx, i want uart without fifo,i configure 3 uarts independently and use the
#define APP_UART_INIT(
P_COMM_PARAMS,
EVT_HANDLER...
Hi Nordic forum.
We wanted to update the bootloader over the air. Initially, we had a very plain bootloader (the one provided in the example) but later we added a timer...
Hello everybody.
Please answer my question.
I repeated the Bluetooth pairing ON → OFF of my smartphone and DK 52
(PCA 10040 + HRM) and checked the connection, I encountered...
