Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
devzone.nordicsemi.com/.../
Using this link I'm able to build sample code in nRF52 SDK in Ubuntu.
I've customized board based on nrf52832 (Bluey Board) & ST-link v2...
Hello,
we are planning to implement bluetooth chip in our device.
So for implementation we need nRF52 DK development board on loan basis.
Let me know whether we will...
Hello everybody! I am working with nrf51822 n51822 qfaah2 17138q and i tried to load my code on it, but i always receive this error message. Could you help me?
with this...
Hey all,
I'm trying to get the Nordic UART service with the nRF Toolbox App (Android).
But always when I send "Hello" from the nRF Toolbox App, for example, I don't only...
Summary
I do a bootloader/softdevice update via the dual-bank BLE DFU example from nRFSDK11 with SD132 v2
When the new bootloader (the SDK11 bootloader example ported...
Hello,
I have a strange behaviour in my project and can't find the cause:
I have connected a TMP116 temperature sensor using TWI with SDA at P0.03 and SCL at P0.04 using...
Hey I'm looking at the radio page for the nRF52 DK and at there is a Capacitor C10 that goes between the DEC4 and VSS pin.
The BOM for PCA10040 shows the following line...
I use FreeRTOS in my application (nRF52, SDK14) and want to statically allocate memory for task stacks. Unfortunately, the FreeRTOS port in the SDK is oooooold, version 8...
Hi All,
I am new here, i wanted to know if i can perform encryption algorithm using pca10040. Do we have cryptocell on nrf52832-dk?
Thanks in advance.
Regards,
...
I have a number of nRF52832 beacons that advertise at a set interval.
All the beacons have a "device_name" set as "ECO".
My application scans for these beacons with the...
In the infocenter there is a whole topic about single and dual bank ( infocenter.nordicsemi.com/index.jsp
It states: "All firmware updates are performed as dual-bank updates...
Hi guys,
I want to know whether the provisioning beacon can relay by the relay node or not?
If not, when the unprovisioned device's radio is not in the range of the...
Hi ,there
i have tcrt1000 optical sensor wants to interface with nrf51822 so can anybody provide me the tutorial on this things with a code...
cheers,
Abhijeet
I have created a Piconet using nrf52840(s140). The 'Central' application was built on ble_app_uart_c example, which is now successfully connecting up to 7 peripherals. The...
