When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I am working on a project in Nordic SDK 8.1 that requires using a timer. I am confused where I need to define the timer though (using APP_TIMER_DEF). If I put it right after...
I am working with the SDK 12, nrf52832 low_power_pwm example. I am concerned about the power consumption I am measuring.
I am trying to produce a 1khz PWM for an LED (the...
Howdy,
I am having difficulties writing to NVRAM (reading appears to be fine and is reporting 0xFF's everwhere). I am using a rather old SDK and SoftDevice 110 (version...
How much is the nRF52840 USB DP/DM pins impedance in transmit mode?
There is no info in datasheet .
On the PDK board there are 39 ohm resistors connected in series with...
The engineering B errata mentions PAN 186, that the current consumption in System ON Idle is increased if High-Voltage mode is used. Is there any information available how...
Hi everyone, I'm having troubles with a project using softdevice, and I think it could be a memory problem, I just wanted to confirm that the addresses are correct and there...
Why was this removed? The SD 3.0 docs show only random static and public as options and I get bad address for the others which is consistent with the docs. We were using random...
Hello
Nordic Team.
I controling nrf spi.
testing for example nrfSDK14.0.0\example\peripheral\spi\pca10040\blank\arm5_no_packs\spi_pca10040
/**
* Copyright (c...
Hello everyone, I want to run project ble_uart on NRF52832 in Keil.
At the beginning of the main.c I add
#define BOARD_NRF6310
But get error
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
hi team, i am using nrf52840. is there any hidden services placed in nrf connect app android for gyroscope or we want to create our own services. and also one doubt wat is...
Hi,
I wanted to know the peak current of the nRF51822 chip using the softdevice 130.
I was looking through the documentation and found on the S130_SDS_v2.0.pdf the information...
It would be nice if libraries in the SDK contained more asserts about preconditions and postconditions. For example, since app_timer requires the lfclk running, the app_timer_init...
hi, i have downloaded nrf5-mpu-example sdk 13 from github. made necessary changes to work with sdk 14.2 for nrf52840. the kit is advertising when i check it in nrf connect...
