Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
When trying to follow this guide for testing bluetooth mesh on a nRF51 dev-board Cmake returns this error:
../build $ cmake ..
CMake Error at CMakeLists.txt:16 (include_directories...
Hello, I have had luck in Keil making two NRF52 connect with NUS, central and peripheral. My goal is to have one central speak to multiple peripheral at same time via a piconet...
Hi
I have just baught some nRF52840 DK boards,
and I can test the BLE throught between those nRF52840 DK boards successfully.
This indeed help us a lot about research...
Hi,
I am using SDK 12.2.0 with my custom board. As per the my requirement, i need to ground or set logic 0 of my gpio pin no. 12.
So, how can i do this?
good morning to all
I wanted to ask if anyone has a design of nrf51822 where an external temperature sensor is used, to know how the connection to the chip is. Should I buy...
Hello,
I am learning about the behavior of "Notify" transmition.
From some web sites including below, I understood as follows.
devzone.nordicsemi.com/.../
So could...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
I'm transmitting data packets each of 48 bytes in the form of notifications using Bluetooth 5.0. When I observed the logs over sniffer, I see that the packets are fragmented...
Hi,
iam new to all this and hardly find answers for my question:
Is it possible to pair a nRF51422 with an Ant+ remote especially Bontrager TransmitR and use those remote...
nRF52832
Hi,
I am a little confused as to what component uses ble_flash (...drivers_nrf\ble_flash\ble_flash.h/c) and why? What is the difference between this and SD...
Hello all,
I've ported the buttonless DFU example to my project without the buttons or the LEDs, but I only tested the bootloader and not the uploading capabilities with...
I want to know the details of "DTM testing using nRFgo Studio".
On page 52 of "User Guide v1.4 of nRF51822 Development Kit" says, "For details on how to use the Direct Test...
Hi.
I bought the nrf51822 kit, and I have questions to ask.
I know that there are many sample code provided by nordic.
I know that the sample code will run...
Hi!
I am working with an application were two nRF52832 shall communicate over UART in half-duplex 1-wire mode (similar to what is described here but I use different pins...
Got one new Thingy52 and worked all nice with both Android and iOS teminals.
Then I have tried to upload new firmware using the iOS.
Loading new firmware progress was...
