System Info: Hardware: M3 Max OS: Sequoia 15.3 Following the instructions outlined in the readme of: github.com/.../nrf-docker Docker fails to build an image on Apple Silicon...
Hello,
I am attempting to build the Matter template using only the nRF54L15’s internal memory. While the build occasionally succeeds, it more often fails, and I am unsure...
Hi,
I'm currently using NCS v2.9.0 under sysbuild and have recently been using board definitions from different directories. My recent projects possess a "boards" sub-directory...
Hi,
a couple of days ago, I had to install some STM plugins for VS Code (I'm sorry ).
In the process, the "CMake Tools" from Microsoft were also installed. I remember...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Hello.
I get error 0x10 (error for invalid flags) when i want to write to peripheral with my master module. I use the same code i always used, and i didnt change anything...
Hello.
I written code for nRF51822 w/ MPU6050 in S110(8.0.0) and Keil.
I tried to setup gyro as bellow.
twi_master_init(); => mpu6050_init(MOTION_SENSOR_ADDRESS);...
Hello
I have connected the nrF51-DK board and it was recognized by the computer.
I have managed to put in in a boot loader mode.
Since I switched it to boot loader...
I have three pca10001 boards. One is programmed as multilink central and other is programmed as multilink peripheral. when both peripherals are connected to central, the central...
I'm a newbie for Nordic development.
I just noticed that softdevice, app, and bootloader share the same CPU, RAM and Flash at the same time. This three software modules...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi
the PWM frequency should reach 8MHz( duty cycle is 0.5 )when use timer0(16M) without SD.but i revised timer demo code from peripheral and only get 50KHz.i don't know...
Hi everyone,
I've found a few posts and a lot of info but I'd like to know if there is an existing example that merges a few of the examples found here ( github.com/.....
Hello.
I want to retain the value of a certain variable after issuing a system reset (sd_nvic_SystemReset).
Can this be done without storing it in the flash memory?
...
Hello.
I use SDK 8.0.0 and PCA10028 board. I try connect board to the Windows 8.1 PC ( i have Tablet PC and Desktop PC with BLE dongle). For connect board to Windows i...
I think I understand what these two flags do, the SYS one returns the system attributes, which I assume means data representing the CCCD for the service changed characteristic...
Hello,
Is there any compatible arduino lcd with existing library for the nRF51 Chipset?
So I can just plug it on the nRF51-DK, include the library and "lcd_wirte("text...
Dear Developers!
I'm a newbie in nrf51822
My Project needs to change between central and peripheral role. How can I apply OTA DFU with S130 soft device ?. In nrf51822 DFU...
