Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Today I tried to update the SoftDevice of my project. I was working with the experimental NUS example with the old S310 SD (1.0.0). Because I want to communicate thru ANT...
Hello everyone,
I'm developing a security scheme in which the firmware verifies that the nRF51822 is the same as the one in the factory to which the firmware was installed...
Hi -- Can I run direct test mode on the nRF51-DK?
I've found the Direct Test Mode window in nRFgo Studio, but my board isn't available in the "Set up on ... " pulldown...
Hi,
I'm trying to implement a device including a PWM counter and a high resolution timer working with softdevice stack 110. Per the examples I got from this site, I'm using...
Hello! I'm trying to use s130 as peripheral.
I flashed nrf51822 with s130 stack. Opened peripheral example and build it with .ld file for s130.
After it I flashed this project...
we have a 2 chip soln. nrf for Ble, Atmel for main application.
config data is located in the Atmel part. Config data also has BT Device name, ADDR, Adv Params etc.
I...
I am thinking to use IoT SoftDevice in a project, but I read that
" This SoftDevice is a technology prototype only. Therefore, it should never be used in production ." This...
Hi there,
I'm trying to program an external nrf51 board (Xuntong 5518) through the nrf51-DK Debug out connector. So far I have no success and I'm wondering if I have the...
What exactly are the "glitch" issues with the PWM master library ? I see there have been some recent updates, but no clear indication as to what issues remain or have been...
Hi,
How to upload and debug application program to the beacon with S110_nRF51822_7.1.0 and bootloader (DFU) using J-LINK? The standard procedure takes into account OTA...
Hello,
I want to detect the advertising data of more then one Beacon with the SDK51 and read the TX_Power for a location-application.
I´m inexperienced in stuff like...
will gazell device fall-back immediately to out-of-sync state upon reaching the max tx attempts even if the sync counter is still less than the set sync lifetime?
thank...
I got a nRF51822 based module and I loaded a slightly modified application based on "ble_app_beacon" example in nRF51 SDK via SWD interface using J-Link. The code has been...
