Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I tested sdk16.0 with secure uart debug example, that DFU needs to enter bootloader twice(press button4 and reset twice), first time to update setting file, second time to...
Hello,
I am developing using nrf51822 and J-Link.
In the Keil4 version, the RTT viewer worked fine, and only the project was migrated to the keil5 version,
but the RTT...
I'm using PCA10040 to test nRF52832.
But I can't see J-link device after connecting USB.
I installed J-link(segger), nRFgo studio, nrf command. But I can't see my PCA10040...
Hello, we are using the ble_app_uart example code, and are trying to modify it so that if a certain UART sequence is received from the connected microcontroller, it will disconnect...
Hi
I'm working on a project interfacing the nRF52840 board with the lis2dh12 accelerometer
I'm using SDK 15.3, basing my code on the provided driver and information...
Hello!
Now I have two devices about nrf52832 .One is central and another is peripheral. So I want to transfer the peripheral mac address to the central via nfc.
I do...
This is the config fun followed。
one sample every 125ns,one ant get 12us =96 samples.
and first 2+32 samples is ignored。
*******************************************...
I've already tried to set some zephyr configs, but n51822 to run as peripheral it nedds at least ~20KB
Have anyone got success or all the nrf51822 QFAA H2 will really never...
development environment： SDK 14.2 , NRF52840 as central and NRF52832 as periph for Bonding: Passkey Entry, Central displays, and the error occur on nrf52840.
I want to know...
Hi all! I am currently using an nrf52840, mesh sdk v3.20 and sdk v15.30
I have the following scenario which I am trying to solve:
I am receiving a new GAP name for each...
In an earlier thread ,
[quote userid="17188" url="~/f/nordic-q-a/33649/j-link-the-firmware-of-the-connected-j-link-does-not-support-the-following-memory-access-read-0x02000004...
I'm using the nus_c service with multiple central connections. Obviously, I need the connection handle in my event handler - ble_nus_c_evt_handler(ble_nus_c_t* p_ble_nus_c...
Our product use two NRF24L01+. One is for transmitting and another is for receiving. They communicate by 250Kbit/s. It is pre-production.
Now, we want use nrf52810 to instead...
I just trying log via Segger RTT viewer, followed the the same procedure as that of serial_lte_modem sample in my new project and could not see logs showing in the viewer...
I am working with nRF52 DK, SES4.30 and SDK 15.3 with SD 132.
This error just started occurring once I set up app_timers. My code for setting up my timers is below:
...
