I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi Nordic Devs,
For my project, I am looking for couple of tactile SPST (Single Pole Single Throw) switches like this one . Would appreciate any alternatives that are cost...
Hi!
I realize that the paint on this is still drying, but I'm wondering if anyone is seeing the following behavior?
I can run an program based on this API once. When...
I'm developing a custom solution using the nRF51822 CFAC. The nRF518-SDK version 6.1 does not explicitly claim support for the CFAC. Will there be issues using this SDK and...
In my plan I have a rf moudle NRF24l01 , this is not important, so , If you see in figure 1 we have radio masts that send waves in around. we can't accept this. my plan for...
I have a system where any two identical devices need to establish a communication between each other, without any prior knowledge of which is master and which is slave. Currently...
I have the 51822-DK. I was finally successful in uploading the Heart Rate Monitor example application to the chip with the S110 but now it looks like nothing happens. I downloaded...
Hi nordics.
I am trying to do s120 multilink_central example.
However, this example doesn't work well, and I cannot debug central example.
-Environment-
board...
Hello,
I am working on pca100028 and using s130 softdevice(SDK 6.1.0.0.). I am trying to see UART log on pc. But my code get stuck at the following while loop.
void simple_uart_put...
I am using ATmega32s to drive the nRF24L01+ chips and a low dropout 3.3v regulator (TI’s LP2950) to power the nRF from the five volt buss.
Both the transmitter and receiver...
We are seeing bonding issue between Nexus 6 and our 51822 based product. After inspecting the sniffer capture, we observe that the phone advertises its IO capabilities as...
I have an nrf51822 S110 based application that tries to discover the primary services on the GATT server at every connection of a central.
Unfortunately, the central does...
Hi,
I have read all the answers about ANCS, it seems there is no conclusion can be resolved the problem, that is "It seems working first connection. But after rebooting iOS...
Dears:
I'm using nRF51822 with softdevice S110 . And I want to know, how can I switch the communication mode betwean BLE and 2.4 G ?
If possible, could you provide me...
According to ble specification [1] and based on my test with iOS, the cts_c library seems to have bugs on a process decoding adjust reason data.
Here is a simple diffs...
