Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi:
The nRF52840 VDD voltage supply range is 1.7~3.6V
So if we provide 3.3V to VDD, the voltage ripple spec. is still 1.7~3.6V?
Or other spec. that we need follow? ...
Hi,
I am evaluating a BLE beacon solution and the nRF52 seems attractive. If building a solution where an appliance I will develop will listen for a BLE beacon that I also...
Hello,
I am new on keil and nrf, I am trying to merge nrf52832 sdk15.0 ble_app_hrs example and this custom service
I want to send command from nrf connect app to my nrf52832...
Hello,
I am working on a BLE application for the Thingy91 which needs a lot of dynamic memory. In the Zephyr specification values of up to 16kB are supported. I tried to...
I am using zigbee light_control examples in nRF5_SDK_for_Thread_and_Zigbee_v4.0.0 for my zigbee projection.I want to know how the zigbee network build and which command will...
Hello, I have been using segger embedded studio v4.16 for almost one year using free license. today it says my evaluation period is expired. But they say it is for unlimited...
I have a setup with one transmitter and three receivers. The transmitter (nRF24L01+) sends a message to the receivers (nRF52832, using SDK v15.3.0) every 10 seconds. The receivers...
Setup: Segger Embedded Studio v3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 Custom Board
Hello,
I based my code off of your Zigbee cli_agent_router example. In the...
We use both the iOS and Android DFU library to support DFU through our mobile application. Recently we found that Samsung phones running on Android 10 have a problem with...
Hi,
I'm developping some test suite for one of our ble products in development, and I'm encountering some unexpected behavior using pc-ble-driver-py.
The test I perfom...
Hi, this is probably an easy one. Starting with the ble_app_uart peripheral example, I am customizing an application. I observe that two events with IDs 58 and 85 come through...
I have setup a timer interrupt whivh fires at about 10 seconds which I can follow on an RTT viewer the ISR demands two ADC's to convert the voltage levels on their pins, I...
Hi Team,
When we add RNG peripheral Driver related code changes to our custom project we are getting linking errors, but when we compile individual files it is compiling...
Summary
I am using UARTE on NRF52840 at 115,200 but am experiencing "bit loss", i.e. the UARTE is losing a few bits in the incoming stream causing corruption of all incoming...
Hi,
I’m new to this dev environment and hoping I may get some help.
I’m building my backup application binary and want to store it in the upper ½ of flash on my nRF52840...
