i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello guys,
I programmed the gps sample on the nrf9160 DK, but I get:
I added a printk to see which of the at_cmmds were failing but I get inconsistent results. It used...
Hi,
Working with ads1220 which runs on SPI. There standard SPI pins - dout, din, sclk, drdy. In its datasheet there is written it is possible to merge dout with drdy to...
How to upload code to nrf52840 using arduino or usb2ttl as I have ms288fv2 help me guys or suggest me the board using which I can upload to code to nrf52840 if and ms88sf2...
Hello:
I'm testing nrf9160's A-GPS function, and I find that an error of SUPL will be reported at runtime:
I use master branch of the nrf repository(nrf/samples/nrf9160...
I have a Windows 10 laptop (Acer Swift SF 514-52T) where I have installed the setup for nRF9160 from "nRF Connect for Desktop".
All steps followed.
I got some issues...
I've got my application wrapped in mcuboot for HTTP-based firmware updates which is working fine. In the past couple days I've enabled CONFIG_NVS using the code in zephyr...
Hello all, This is my first post on your DevZone. Setup details: nRF9160 DK Board: 0.8.3 nRF Connect SDK tag: 1.2.0 OS: Windows 10 Pro LTE Network: NB-IoT on B3 and B20, Operator...
Hello, I'm using nRF52811 and It works with 1.8 voltage on it's VCCs. Is it possible to use a micro SD? Should I use a voltage level translator (for example TXB0108)? I know...
Hello all,
I try to import Keil project into Eclipse with Makefile. I managed put all my source file to be compiled, and my include paths etc.. in my Makefile
In Keil...
Hi,
I am working on one application in which I want to sample ECG at 1000 samples per second continuously and battery value at 15 seconds interval. I am configuring two...
Hi,
I'm trying to connect my phone ober BLE with the nrf52840. The first x attemps always work (connect, disconnect, connect, disconnect, ...) but after some time no further...
Hello guys,
I`m pretty new in socket programing, I have a question , is there any way to trigger an event for a file descriptor that is used in poll() function ?
For example...
Hello DevZone,
Recently I've been testing connecting multiple servers to one client and fiddling around with some settings regarding timing and packet size.
In the following...
Hi everyone,
Recently, I have bought two nRf52 DK, and I want to test the latency between central and peripheral in 2Mbps.
Can someone give me some suggestions about where...
I develop BLE Beacon device using nRF52832. I want to set the device name by combining "XXXX" and the lower 3byte of MAC Address. "XXXX" is used to recognize it as a company...
