I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
We've been using the nRF51822 sniffer to listen to packets. One of our developers used to be able to use it decrypting packets without a problem (He uses 32-bit system, firmware...
S110 v8.0.0 / ble_app_hrs_with_dfu
I want to enable whitelisting.
In the advertising_init() function I have:
ble_adv_modes_config_t options = {0};
options.ble_adv_whitelist_enabled...
Hello,
I'm testing current time service client example on SDK 8.0.0 with iOS 8.2.
while the device can be search by android and pair,the IOS 8.3 has see nothing.
how...
Hi.
I'm working with nrf Temp, in the file TemperatureDataParser.java, and I want to send out a note when the measured temperature has passed the chosen SETTING(distinguishing...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
I am trying to make the experimental_ble_app_uart for s110 work using SDK 7.2. It works fine without any modifications, but when i turn off Hardware Flow Control in the UART_init...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello, I am new to Nordic NRF51dk and I'm working on the SPICommunication_module c.
For the switch case statement, I am trying to understand what the spi_master_evt.evt_type...
Now, I'm using "nRF51\peripheral\temperature" example to test something for my nRF51 DK board.
I have upgraded sofeDevice s110 v8.0.0 in DK and I can use Keil "Download"...
I am using Unity3D BLE Plugin by Shatalmac ( www.assetstore.unity3d.com/.../ . Upon using the example code, it is discovering the UARt custom service, but dont know why it...
I am really struggling getting anything to work on my revision 1 module and as it has nothing connected at this moment all I can use is BLE or UART to observe any function...
Hi,
I would like to change the the advertising interval of the beacon kit in the sample ble_app_beacon app; however, I could not figure out where this parameter is. I see...
Hi,
I want to connect a rotary encoder.
So I have 2 pins of the nrf51822 connected to the encoder and I have to check which one change first to increase or decrease the...
