Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I am trying to connect to one specific device. To make this I am advertising with the whitelist. The problem is that the whitelist do not seem to work. I got the...
I am using the nRF51822 module. I am using the following code to set my device discoverable:
ble_gap_adv_params_t adv_params;
ble_gap_addr_t *whitelist_addr[1];
...
I've got a custom board with an nrf51822 (ic rev 2, QFAA), and I'm trying to understand some unexpected current draw that I'm seeing from the board. Currently the entire custom...
Hey there,
Red Bear Labs sells a board with a NRF51822 Module on it. From a past post I have found it is said:
"embedXcode supports the nRF51822 MDK board for both the...
I am playing with S130 to behave as a peripheral device and a central observer. This is working great.
I am new to the central side of things and have a quick question...
Hello,
I have looked at several posts on here, including-
https://devzone.nordicsemi.com/question/3769/nrf51822-to-nrf24l01/
And followed the code, but I am trying to...
After I installed keil and nrfgostudio, I run nrfgostudio, but an error happened, which says" an instruction of 0x6b607a05 quoted the RAM of 0x094af43f, but it cannot be read...
I want to program Jtag inside Anti-lost Tag nrf51822 Module Bluetooth Low Energy Sticker.
Following are the specifications of Anti-lost Tag nrf51822 Module Bluetooth Low...
Hi, I have purchased a Nordic nRF51DK which works perfectly. Suddenly I purchased an EaEpaper and start to follow this tutorial developer.mbed.org/.../Homepage to map it to...
I have used sofdevice v7.1.0 and nrf51 sdk 6.1.0
the ble_app_hrs project which has support of dfu is not discovering the dfu services.
i have enabled the BLE_DFU_APP_SUPPORT...
Hi...
Do you know how the " ble_app_hrs -> experimental_s110_with_dfu example" in SDK 7.2.0 examples works? how to switch to DFU and how to do over the air update?
i...
I am using NRF24L01 modules sold on ebay. I have 3 boards where these modules are soldiers and notice a big difference in range. More distant of other components, better range...
Hello everyone, I must read several data stored in a external E2prom and send them to a smartphone. I thought to do this by use of Record Access Control Point, so I can to...
