I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hi to all!
I have few questions about throughput when using s120:
What is the max number of packets that could be send/received in one connection interval when using...
I've created a BT peripheral based on the app_proximity example (SDK 8.0) and added code to implement paring with a static PIN per examples posted here. It works as expected...
Is it possible to have 1micro second interrupt using timer 1?
I am unable to achieve it.
If I try for 4micro second, I observe toggling of pin at 8 micro seconds?
...
Some examples require SDK 7.1, while the newer tutorials use SDK 8.0. I'm not sure how to switch between the SDK versions in Keil. I see the below lines in my include paths...
Hi.
Currently, the following results came out in the power-saving support .
■Our App
・Advertising Status
1.04mA ~ 1.13mA
・Connection Status ★1
1.044 ~...
Hi.
After stopping the Advertising,I measured the current.
For some reason, usually it is consumes about 1.1mA.
Because too large current consumption,
As a result...
Hi I using nRF51822, and want to know about the Nordic driver support LMP feature
Do you have any document about driver support? Or any software development document except...
Hello, I need to create a high resolution/high frequency PWM signal on the nRF51822. I have been using the new PWM library in the 8.1 SDK and can't quite get there.
From...
Hello. After a couple of s210 and s310 projects, I am attempting an s120 project. I built a client SDK but sd_nvic_EnableIRQ returns error code 0x2009 or NRF_ERROR_SOC_PPI_INVALID_GROUP...
I'm running the "Beacon Application for Eval Board" example for the S110 soft device on an nRF51822.
( devzone.nordicsemi.com/.../a00070.html)
I'm using another BLE...
Hi,
I was wondering if it is regual that configuring softdevice for a low frequency oscillator 32.768 kHz using the function:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
