So I will have 2x physical UART provided on my board. I am using printk(), and I want to choose which UART handles console traffic by config options.
How to achieve that...
I have been working with 2.9.1 but went back to a project using 2.6.1 to flash a nrf5340dk and can still compile it, but now cannot flash the nrf5340dk. I am getting this...
Hello,
I'm trying to use SLM application on ctcc/nrf9161 hardware ( https://github.com/nrfconnect/sdk-zephyr/tree/main/boards/ct/ctcc ) however it seems I'm not able to...
Hi, I have to integrate on my MQTT application , location library using GNSS. Actually I am using location library on cellular. I want to use exclusively GNSS. I am developing...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Good afternoon,
We are developing a consumer product that is using the nRF8001 as the BT peripheral. We have a question regarding certification; do we need to undergo...
Dears，
To support Bluetooth 4.2 in the nRF51822 product page on S110, but only support 4.1 in the SDS document, I want to confirm the support of the S110 V7.3 and v8.0 for...
Hi,
for my application, I want the processor to wake up once every 8 hours, do a 1 second analog measurement, broadcast the results and shut down. When activated by a switch...
Hi,
I am having some trouble using fstorage to write data into flash. I want to store ~20 kB of sampled data before processing it, and I am storing it just below the bootloader...
Dear every one.
My company has ordered 20 development kit NRF52840 for our Mesh project. We will receive these board 1 week later.
But i have 1 preview development kit...
Could you please help me out on how to read my EMG sensor values and display it via the Nrf tool box. I have a redbear nano v2 and the digital output of the sensor is received...
Hello,
I'm having some issues with the MAXCNT limitation of 256bytes because I want to send larger packets and receive packets through the SPI Slave interface, which is...
I have an external board based on nRF51822 QFAC. I have a nRF52 preview DK. Will it be possible to detect my external board if connected via the preview DK. I tried and the...
Hello,
We've a Custom board based on nRF52832, it works fine in beacon mode using the Synth Clock (else it doesn't work):
// <o> CLOCK_CONFIG_LF_SRC - LF Clock Source...
When using the PPK to measure the current of our custom hardware the lowest range doesn't give logical results. (Either the PPK python GUI or nRF connect) When the nRF52 on...
Reference: nRF52840 DK Evaluation Board Schematics
The following inductors are lised in the schematic:
L1
3.9 nH
High frequency chip inductor ±5 %
0402 ...
I am working on windows xp command prompt and using nrfutil version 3.5.1
I want to do a Device Firmware Upgrade over BLE through my nRF52 DK board on a custom element....
Hi there,
SPIM3 running at max speed (32MHz) will be the fastest external interface (along with QSPI)
Because I would like to make to most of it, I wondered if you had...
