Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I see there is a serial bootloader dfu example, however I am unable to find an OTA Mesh DFU example.
How can I exercise the Mesh DFU OTA (not via serial connection) in side...
Dear Nordic,
i just implement uart example in one of ble example(central and peripheral example) ported from ble uart app example
i face some problems
i configured pins...
hello,
i am using the Nrf52840 , SDK version 15 with segger embedded studio.
i am developing simple application but i got this issue. i already add the reference in the...
Hi,
I am trying to merage "ble_app_hrs_c" & "usbd_hid_generic" examples.
After programing, I Insert dongle into USB with SWD , BLE and USB run normaly.
But if i insert...
When calling nrf_drv_twi_tx() once like in the snippet below it works, but when the function is called two or more times sequentially, it fails. However running a nrf_delay_ms...
With respect to Softdevice versions SDK_14.2.0_17b948a and SDK_15.0.0_a53641a
I have a question about softdevice function:
sd_ble_gap_lesc_dhkey_reply()
and its parameter...
Hi Sir,
In this project, we design w/ nRF51802-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028).
We can test...
Apologies if this is a duplicate post:
I am successfully making nRF example apps in nRF5_SDK_12.3.0_d7731ad using GNU Tools Arm Embedded version 7 2018-q2-update in Windows...
Hi,
I want to use both UART0 and UART1 at the same time, and run the testing example from https://devzone.nordicsemi.com/f/nordic-q-a/25173/nrf52840-uart1-not-working-in...
Hello,
Using two nrf52 Dev Kit boards for Central / Peripheral. Using Softdevice S132, , peer manager and Segger on Win7.
I have modified ble_uart_and ble_uart_c using...
Hi,
I have downloaded the nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and try to compile the zigbee_light_switch_pca10056 example under segger embedded studio and I have...
We are developing a standalone application. The bulk power is provided by LiPo battery, which can vary from 4.2V to 3.0V as the battery discharges. I have the system connected...
I recently added bonding and authentication to my application. I have two characteristics with CCCDs and they are both broken. One characteristic is "protected" (requires...
Is there a standard/spec for the UUID used for provisionee devices?
I don't see anything in the mesh examples that indicates a standard UUID format is used.
It allows...
I am using an nRF52 DK with Soft Device 6.1.0 on a Windows platform.
I am trying to add a new BLE Service and calling function sd_ble_uuid_vs_add() but get NO_MEM error...
