Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello Community,
I am trying to use Black Magic Probe, an open-source ARM GDB debugger to develop an embedded ARM application using an nRF52832. Here are the parts that...
I am trying to configure two ports as outputs, setting them to Vdd and toggling them. The two ports in question are Po.06 and Po.07.
Here is my code to configure these ports...
Hi,
I didn't understand the function of softdevice. I have a custom nrf52832 board. My requirements;
-2 uart,2spi,1i2c
-OTA update
Should i use a softdevice in nrf...
I have been playing around with example projects in SES (I'm using SDK 15.2.0, SES version 3.52a).
Now wish to start a project from scratch, and import libraries from the...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
We work with custom firmware and use the softdevice 2.0.1 on the nrf51822
I upload the firmware as .zip file using the android nrf Toolbox, which works fine, but when performing...
hi there,
i have made the application and dfu working but there is a smal issue. if i program dfu and application from nrfgo studios the dfu run continuously and app does...
Hi, I'm trying to use the light_switch example in the Mesh SDK 2.1.1 to build a small experiment to count how many messages are received by the server when sending a consecutive...
Hello,
I am trying to do USB DFU on (NRF52840 with SDK 15.2) but when i run the nrfutil command it gives an error:
command: nrfutil dfu usb_serial -pkg ble_hrs_combo...
I've setup, compiled and run the BLE Beacon project an have made some changes. Now I need to enable the UART. Simply adding UART files to the project does not work due to...
Hi
We've developed a wearable device and are changing from a rigid PCB to a full flex PCB. I want to know what adjustments is needed for RF output because of this change...
I am running an example from Mesh SDK (v2.1.1) named "ble_app_uart_coesixt". I see device in Bluetooth list, everything is ok. But I need to provision this device using my...
Hi,
I am using a Sparkfun nRF52832 dev board and SES with the Jlink mini to program it.Our project involved the ability to use the micro as a keyboard so I am playing with...
I am working with NRF52832 and S132. I have successfully captured signals with the ADC (with RTC events at a frequency of 500Hz) and synchronized them using this beacon/scanner...
Hello,
I am working on few projects involving nRF52 DK's using the nRF52 15.2.0 SDK. I would like to know which would be a more efficient and reliable way of changing...
