Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi all I just want to use UUID advertisement in solar beacon code for advertising @ 100ms interval I don't need temperature and pressure data .I also want to change type to...
Hi. I'm using the NRF-52 DK (PCA10056) with an SD card module and I'm trying to upload the FatFS example code for SDK 15. I'm using a kingston 8GB SD card and I'm unable to...
Hi all,
I develop program code based on nrf-mpu-magnetomter examples. I code the DMP and complied well . However the program is always stay an error when it starts running...
In my application an nRF52832 acts as a BLE peripheral device which is sending sensor data to an app on a mobile phone. As long as the phone is interested, notification on...
I'm trying to add buttonless DFU to the SDK's template application.
Here is my setup:
Soft Device 6.1.0
Secure Bootloader
Modified Template App (Added buttonless...
Hi,
I am using nrf52832 custom board with s132 to read data from 4 sensors using twi. i have 2 separate TWI with two different sensors on each bus. i am using nrf_drv_tw...
Hi,
I have a question with regards to the system-on sleep current of the nRF52840. This is specific to when using the bluetooth mesh and the nrf_mesh_disable() function...
Hello I am trying to connect nRF52832 development kit to use with Wireless vibration controller store.ncd.io/.../ using mesh module which is transmitting the data to the receiver...
Hi
I'm trying to combine NUS central and peripheral in a single nrf52840. Using SDK V 15.0.0 and softdevice V 6.0.0. Have added both ble_nus and ble_nus_c files and enabled...
I am trying to add Timer2 to light_switch server example. But it fails to compile with a undeclared error for NRFX_TIMER2_INST_IDX. I have set the following macros in sdk_config...
Hello all,
I plan on using the blinking LED authentication in mesh configuration, I have seen the nrf mesh app video where it is done using the app but I want to achieve...
Hello.
I am using the NRF52832 Evaluation board.
If I click the connected board of Device Manager to upload program application, nrfgo studio will be turned off without...
Hello,
I have an existing customer who has products based upon the nRF24L01+.
He would like to upgrade to the newer nRF52x series but is concerned about backwards compatibility...
Dear Nordic
I found a example using nrfx_twim_rx() to scan slaves, I was just wondering if I can use nrfx_twim_tx() to scan slave devices by send zero byte data? I use nrfx_twim_tx...
