Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
I am developing a board, with nrf51422-qfaa chip. To match the antenna I'm using the BAL-NRF01D3 balun. I currently have problems with antenna not working and I'm...
I am running an appliction with S132 soft device, build on top of SDK 12.0.0. Problem is that the application sometimes stops running for ten seconds, or even more, when Bluetooth...
Hi all,
may be you can advice me on a solution.
I need to be able to wake up a system when one of the pins shows more than 1v and I also need to wake up system when...
Hi,
I'm using ble_app_multilink_central to connect different device.In the example, it can connect to the lbs service. If I want it connect the uart service,such as ble_app_uart...
Hi Nordic,
we need to modify bootloader code base on your dfu example. Now We meet a problem that we can't program it by clicking icon "Load" on keil comile project. report...
I am having problem to download SDK NRF51 12.0 example firmware onto Redbearlab BLE Nano nrf51822. The compilation and build is fine. It is shown as
Erased Failed!
Error...
I have a custom board with an nRF51822, running the ble_app_hrs from the 12.1.0 SDK with softdevice s130, using the internal RC clock in a custom_board.h as follows:
#define...
I'm learning about the nRF52 series and so far love everything I see, especially the SDK. But I just got to the point where I'd like to generate precisely timed output, and...
Hello Nordic Team,
As I'm worrying about the max payload lengh that I can notify using soft device s130.1.0.0 on nrf51822 (256 Kb Flash/ 16KB RAM, SDK10), I thought about...
Hi,
I'm porting our project from sdk10 to sdk12 with SD S132 V3.0.0. I cannot find a way to reset the device in app and boot in bootloader in order to do a OTA update....
I have a working custom DFU bootloader based on the official bootloader from the SDK 8.1.0.
Updating the normal application code works without any problem.
Now I want to...
Hello all,
I try to trigger two events with two different periods, the first at 200ms, the second at 300ms. When I set the same period for the compared value, it works...
Hello,
I am tring to do a Bootloader update OTA using the bootlader DFU Dual Bank. Application update OTA is working fine while it is not the case for Bootloader update...
Hi,
I can't get my head around the cipher and auth used by SD132 in BLE (nrf52832,SDK12).
Could someone please explain which HW blocks and SW libs are used for encryption...
Hi, I'm trying to create a custom PCB that uses nRF52832-QFAA and a Meandered trace antenna.
The PCB's environments are 4 layered, FR4, 1.6mm thick, and green PSR ink....
