Hi,
If you use the following settings, an error will occur during commissioning.
Board: Custom board
SDK:ncsv2.9.2 OS: Windows10 Sample code:Matter Lock bord target...
Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hi, on nRF54L15 Dev Kit, we are trying to validate our sleep current consumption. We are seeing sleep current of ~100-300uA, when it should be a fraction of that. As per datasheet...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
Hello,
I am implementing the Physical Activity Monitor Service which looks like this:
/* Physical Activity Monitor Service Declaration */
BT_GATT_SERVICE_DEFINE (...
We have an existing application that is based on asset tracker V2. It has been running since version 1.7.0 I have migrated to V2.9.0 a long time ago and it is running flawlessly...
Hello. I am trying to connect nRF 52840-DK and LTC 5800-WHM with UART. The communication conditions are as follows. Baud rate: 115200 Data: 8 bits Stop bit: 1 bit Parity:...
Hello Community,
I am trying to use Black Magic Probe, an open-source ARM GDB debugger to develop an embedded ARM application using an nRF52832. Here are the parts that...
I am trying to configure two ports as outputs, setting them to Vdd and toggling them. The two ports in question are Po.06 and Po.07.
Here is my code to configure these ports...
Hi,
I didn't understand the function of softdevice. I have a custom nrf52832 board. My requirements;
-2 uart,2spi,1i2c
-OTA update
Should i use a softdevice in nrf...
I have been playing around with example projects in SES (I'm using SDK 15.2.0, SES version 3.52a).
Now wish to start a project from scratch, and import libraries from the...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
We work with custom firmware and use the softdevice 2.0.1 on the nrf51822
I upload the firmware as .zip file using the android nrf Toolbox, which works fine, but when performing...
hi there,
i have made the application and dfu working but there is a smal issue. if i program dfu and application from nrfgo studios the dfu run continuously and app does...
Hi, I'm trying to use the light_switch example in the Mesh SDK 2.1.1 to build a small experiment to count how many messages are received by the server when sending a consecutive...
Hello,
I am trying to do USB DFU on (NRF52840 with SDK 15.2) but when i run the nrfutil command it gives an error:
command: nrfutil dfu usb_serial -pkg ble_hrs_combo...
I've setup, compiled and run the BLE Beacon project an have made some changes. Now I need to enable the UART. Simply adding UART files to the project does not work due to...
Hi
We've developed a wearable device and are changing from a rigid PCB to a full flex PCB. I want to know what adjustments is needed for RF output because of this change...
I am running an example from Mesh SDK (v2.1.1) named "ble_app_uart_coesixt". I see device in Bluetooth list, everything is ok. But I need to provision this device using my...
Hi,
I am using a Sparkfun nRF52832 dev board and SES with the Jlink mini to program it.Our project involved the ability to use the micro as a keyboard so I am playing with...
I am working with NRF52832 and S132. I have successfully captured signals with the ADC (with RTC events at a frequency of 500Hz) and synchronized them using this beacon/scanner...