Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Dear Nordic Team,
Thanks for supporting.
currently i am working Single channel scanning with ble_app_uart_c example. In continuous scanning missing beacons. Please support...
Currently, in my application, any iPhone can attempt to read from one of my protected characteristics and initiate the bonding sequence. I have it set to "just works" mode...
Can anyone tell me if there is a specific problem on the nFR 51 using the 12.3 DK, where a disconnect is seen when it connects? I'm using Android Lolipop 5.0 on a BLU device...
Hi,
Im migrating from SDK8 to SDK12
app_timer crashes
Debugging at app_error.c shows m_error_data to be :
softdevice, pc 0x000104AE, fault ID 0x00000001 error_info...
Hello, trying to understand how to replace just the bootloader and s112 SD (app not installed), presently getting Insufficient resources.
First, mergehex -m softdevice.hex...
Hi,
Has anyone attempted to first transfer the entire image package to the external flash over BLE and then use a background DFU library to transfer from the external flash...
Hello,
I've got a NRF52840-DK development kit and tried to configure it with a ATT MTU size of 512 bytes (larger than 247 bytes). I've activated data length extension and...
HI all,
I'm trying to get the Thingy Mesh Demo v0.1 working on my Thingy's. I am using the same SDK version as used in the demo ( Nordic nRF5 SDK for Mesh v1.0.1) and I...
I was able to follow the "quick start" guide for Mesh DFU and got things working with 3 nodes.
1 node (the serial host hooked to the PC) was programmed with:
bin/softdevice...
Hi to all,
i am developing a device with nrf51822 soc. i am using nrf51822 custom board, my board is https://pl.aliexpress.com/item/2V-3-3V-NRF51822-Bluetooth-4-0-Wireless...
Hi, everyone.
I am currently doing research for our new project - IoT alarm system for smart home.
One of requirements is Wi-Fi / BLE combo chip / module . Multi-protocol...
Hi all,
in Central mode I would like to retrieve the list of all the devices present.
I have developped a litle USB dongle, and I need to list alls peripherals, but after...
Hello,
I am using hardware PWM on NRF52832 in order to drive a MOS. I found something unexpected with the rates. i understand the PWM rate is determined by the clock divider...
So I'm trying to merge the ble_app_uart example with a project of my own, using SDK 14.2.0, but keep getting errors with the ram.
At first, my own project's ram start was...
