Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I am currently working on a master thesis at NTNU, and are working on a sensor system based on audio collection and classification (Machine Learning). Power consumption is...
Hi Support engineer,
I am quite new to Nodicsemi devices, I am going through some getting started tutorials, but I found there is no tutorial based on Segger Embedded Studio...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I need to know that What is the maximum datarate for "ble_app_uart" example ?
In the...
I have a question with flash writing of nRF 52. Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source...
Runtime environment:
1.IC:52840QIAA ；
2.SOFTDEVICE:s140_nrf52840_5.0.0-2.alpha_softdevice.hex
Development:
PWM signals of 10 groups of adjustable frequency and...
I am trying to establish communication using SPIM. when I checked the macro definition of NRFX_SPIM0_ENABLED it's present in apply_old_config.h. I am using nrfx_spim driver...
Hi,
I have two 52832 (both on SDK 14.2, S132 v5.1) talking to each other using a slightly modified UART service to support more than one connection.
I have this strange...
Hello,
yesterday I measured the current of our device and found out that it looks more as a square instead of spikes when no device was connected. Found out that when I...
In my code , i use P0.6, P0.8, P1.9 to control three RGB LED.
when I use nRF5_SDK_13.0.0-1.alpha, all is fine,
but when use nRF5_SDK_15.0.0_a53641a, the issure like below...
Hello,
I'm new to Nordic SDK and I would like to ask you for help with change of
GPIO IN_EVENT to GPIO PORT event implementation. The reason is we are using
revision <...
Hi,
I'm using nRF5 SDK v15.0 with S132 v6.0. I have two questions:
1. I use the ble_app_uart example. We want to use high UART baud rate, so I change it to 1M baud rate...
The project I am working on stores information in SRAM while it waits for the radio to get in range and transmit data.
I want to know if I can put items in SRAM buffer that...
I'm trying to learn the DFU process and how to include it in a project under development using SDK 15 and the nRF52 DK. I programmed the DK with the S132 Softdevice and the...
I'm having issues with slow directed advertising. I'm having a BLE peripheral where I want the device to advertise (direct) upon disconnects. I initialize the advertising...
