If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
HI：
I am studying mesh now.But I don't know how to run this example.I think，that proceed as follows：
1.Using provisioner example Configuration each node(element and models...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
When I execute the code below in ble_stack_init (void) , I get an error...
Hello, I am a beginner with the nRF51822, after reading documentation and posts on this forum I can not find a clear answer for these two questions: - Is it possible to modify...
Hello, My software project is based on the ble_app_uart, and after doing some initial timer, PWM and SAADC initialisation tasks, the main loop of ble_app_uart runs for a while...
Hello,
I've got some of the nRF5_SDK_15.0.0_a53641a examples running on my board, the blinky, twi scan etc. all work fine. The twi and spi examples still use the legacy...
I am trying to debug the DFU in IAR.
However, when flashing as is I get the following error:
Sat Aug 25, 2018 20:31:45: ELF/DWARF Error: Unsupported .debug_info format...
In migrating an existing application from SDK 14.0.0 to SDK 14.2.0, I am finding that the first timer I create gets NRF_ERROR_INVALID_STATE on calling app_timer_create() ...
Hello,
I've got the PCA10040 dev kit and it works fine. To match my PCB setup I've cut SB2, this disables the 32kHz osc.
For debugging purposes I went back to the examples...
Hi,
I face a problem when trying to perform a DFU firmware update via command line using nrfutil dfu ble.
I'm using windows 10 and nrfutil.exe version 3.5.0
I am using...
Hi,
In application note 'nWP017 - Antenna tuning', it provides quite a lot information about how to tune antenna.
But, once it is properly tuned, how do I know the matching...
Hi,
When I do not call advertising_start(erase_bonds); then I only draw about 2uA.
When I call advertising_start(erase_bonds); I draw 350uA.
I want to advertise. Then...
Hello Nordic Team,
I have few analog sensors that operate at 5V DC and outputs voltage signal within 0.5V - 4.5V range. I know i cannot interface these sensors with nrf52832...
Hi,
I am working on a project with nRF24L01P. Recently I was trying to make nRF24L01P to transmit packet continuously and i have configure the chip in no_ack, TX and shockburst...
I am using nrf52832 based on SDK14.2 development. I used the air upgrade method in the routine "buttonless dfu". After the online upgrade is successful, nrf52832 will be automatically...
Hi,
we have a nrf51 mounted inside an AC motor housing which we assume is causing an unintended flash erase from time to time (checked with nrfjprog --readcode).
Is...
