Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
I tested the Heart Rate Monitor sketch code (Arduino Primo IDE code) and verified that it works with the Heart Rate Monitor through the "nRF Toolbox app" on my iPhone. I would...
There have been several topics on limitations on ADC sampling rate when BLE is in connection.
However, I didn't see notes applicable to the following case:
nRF52832, sampling...
Hello all,
I have some troubles to initialize the micro SD card with my custom board.
I have used the nRF 52 DK to write a basic code and do some test. For micro card...
I am using nrf52832 DK and am unable to build my light switch example. It throws an error that some files are not included. In the screenshot, you could see the error. I have...
Hey Everyone
I have written a code for using lora rn2483 with nrf52840 using the uart protocol which is configured on 7 and 5 pin. The program was working fine untill i...
Hi,
I am using the nRF52840 DK and the wireless_uart example from nRF5_SDK_15.0.0 to try and receive data from other 802.15.4 sensors. Using the example I can receive messages...
Hello everyone!
I'm very shy to ask probably a stupid question, but...
I'm trying get abitity to change pwm signal via ble.
I've created service, characteristic, then I...
Hello,
I am trying to get a low consumption and I detect that the activation of the ADC increases the consumption. So I am trying to configure the ADC and when I make...
NRF52832 / S332 / SDK 14.2
Step 1: connect to mobile phone as Peripheral Role, and the connect handler of service was #0 that equal to Peripheral-connection handler number...
Hello,
We are using nRF5 SDK14.2.0 and soft device s132, and trying to perform DFU of the Bootloader itself.
The process fail in nrf_dfu_postvalidate() due to wrong HASH...
i am trying to Connect a custom board with the nrf52 over the bluetooth. nrf52 is running with the BLE_nus
.i am trying to connect it with the uuid in the program is like...
Hi. I`m trying to connect two Nortdic Thingy device and receive data in same time(ex. temperature, humidity etc..).
In my application, I can connect two devices in same...
I have most of the SDK up and running with my firmware, but I cannot find where to limit the number of bonded devices to my module.
I could live with just deleting all the...
Hello,
Is there a way to get the output log for the Mesh Light Switch Demo to output over UART instead of RTT? We are using a Fanstel BT832X module containing an nRF52832...
Hello,
I am currently trying to implement SAADC sampling from three channels into the same sample buffer (device is a 3-axis accelerometer, ADXL335). The root objective...
