We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi ,
We know that the nRF8001 use the random static device address . I have the questions below :
A. Will the device get one new address after power on ? or is the address...
Hi,
I need to exchange data between 2 ble modules.
I'm using SKD 15.0.0 and first ble module is nRF52840, second ble module (esp32) acts as GATT server.
I have full...
Hi, I am trying to make nrf52832 as a UART certal. The service UUID and characteristic UUID of peripheral are shown as the following picture. They are all 128bit and quite...
I'm attempting to implement a simple, GPIO driven interrupt system using SDK15, but I can't seem to find any examples using the nrfx_gpiote driver, or documentation on how...
I am currently working on a master thesis at NTNU, and are working on a sensor system based on audio collection and classification (Machine Learning). Power consumption is...
Hi Support engineer,
I am quite new to Nodicsemi devices, I am going through some getting started tutorials, but I found there is no tutorial based on Segger Embedded Studio...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I need to know that What is the maximum datarate for "ble_app_uart" example ?
In the...
I have a question with flash writing of nRF 52. Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source...
Runtime environment:
1.IC:52840QIAA ；
2.SOFTDEVICE:s140_nrf52840_5.0.0-2.alpha_softdevice.hex
Development:
PWM signals of 10 groups of adjustable frequency and...
I am trying to establish communication using SPIM. when I checked the macro definition of NRFX_SPIM0_ENABLED it's present in apply_old_config.h. I am using nrfx_spim driver...
Hi,
I have two 52832 (both on SDK 14.2, S132 v5.1) talking to each other using a slightly modified UART service to support more than one connection.
I have this strange...
Hello,
yesterday I measured the current of our device and found out that it looks more as a square instead of spikes when no device was connected. Found out that when I...
In my code , i use P0.6, P0.8, P1.9 to control three RGB LED.
when I use nRF5_SDK_13.0.0-1.alpha, all is fine,
but when use nRF5_SDK_15.0.0_a53641a, the issure like below...
Hello,
I'm new to Nordic SDK and I would like to ask you for help with change of
GPIO IN_EVENT to GPIO PORT event implementation. The reason is we are using
revision <...
