Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
HI：
I am studying mesh now.But I don't know how to run this example.I think，that proceed as follows：
1.Using provisioner example Configuration each node(element and models...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
When I execute the code below in ble_stack_init (void) , I get an error...
Hello, I am a beginner with the nRF51822, after reading documentation and posts on this forum I can not find a clear answer for these two questions: - Is it possible to modify...
Hello, My software project is based on the ble_app_uart, and after doing some initial timer, PWM and SAADC initialisation tasks, the main loop of ble_app_uart runs for a while...
Hello,
I've got some of the nRF5_SDK_15.0.0_a53641a examples running on my board, the blinky, twi scan etc. all work fine. The twi and spi examples still use the legacy...
I am trying to debug the DFU in IAR.
However, when flashing as is I get the following error:
Sat Aug 25, 2018 20:31:45: ELF/DWARF Error: Unsupported .debug_info format...
In migrating an existing application from SDK 14.0.0 to SDK 14.2.0, I am finding that the first timer I create gets NRF_ERROR_INVALID_STATE on calling app_timer_create() ...
Hello,
I've got the PCA10040 dev kit and it works fine. To match my PCB setup I've cut SB2, this disables the 32kHz osc.
For debugging purposes I went back to the examples...
Hi,
I face a problem when trying to perform a DFU firmware update via command line using nrfutil dfu ble.
I'm using windows 10 and nrfutil.exe version 3.5.0
I am using...
Hi,
In application note 'nWP017 - Antenna tuning', it provides quite a lot information about how to tune antenna.
But, once it is properly tuned, how do I know the matching...
Hi,
When I do not call advertising_start(erase_bonds); then I only draw about 2uA.
When I call advertising_start(erase_bonds); I draw 350uA.
I want to advertise. Then...
Hello Nordic Team,
I have few analog sensors that operate at 5V DC and outputs voltage signal within 0.5V - 4.5V range. I know i cannot interface these sensors with nrf52832...
Hi,
I am working on a project with nRF24L01P. Recently I was trying to make nRF24L01P to transmit packet continuously and i have configure the chip in no_ack, TX and shockburst...
I am using nrf52832 based on SDK14.2 development. I used the air upgrade method in the routine "buttonless dfu". After the online upgrade is successful, nrf52832 will be automatically...
Hi,
we have a nrf51 mounted inside an AC motor housing which we assume is causing an unintended flash erase from time to time (checked with nrfjprog --readcode).
Is...
