I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
We have recently completed the design for a product prototype using the 0.4 mm pitch nRF52832 WLCSP. When we sent it to the board production house, the cost to produce it...
Hello,
i am searching for the possibility to get the information of the number of retransmissions which are needed, to get an ACK from the receiver. The legacy chip nRF24L01...
Good afternoon,
I'm running advertising with a uint16_t service data associated with a 16-bit service UUID.
I would like to update the service data regularly without...
I am trying to communicate with a MLX90615 temperature sensor via I2C and I am able to get the desired response from the sensor, verified with a logic analyser.
I am now...
Hi all,
I am working on nRF52-DK using the light client example under Mesh 2.1.1
I am trying to start and stop the listening for provisioning packets as the idea is to...
I've implemented a Battery Service and battery_level characteristic in my application (0x180F and 0x2A19 respectively) however, when reading the value of this characteristic...
Hi,
I am using one of peripheral examples ble_app_hids_keyboard from nordic SDK for understanding the re connection mechanism. I am using nrfConnect app. I have a few questions...
I am trying to use app_timer library with the provisioner example but I get this linker error.
The multiple definition error is due to nrf_nvic_state being present in...
Hi,
By taking a look at the source code in https://github.com/NordicSemiconductor/pc-nrfconnect-rssi.git, I found the following patch file under fw/src/usbd.patch. It mentions...
We use nRF52840-PDK (PCA10056) with MCU revision Q1AAAA. Given example of secured DFU bootloader (s140) works good. Then we changed MCU on this board to the MCU with Q1AAC0...
Hi to all,
i am working on a project that in it i want use nrf51822 as a peripheral device. i implemented a code but i have a problem, central(cc2540) and peripheral(nrf51822...
Hi,
I am trying to write 16bit, 16Khz, 2 channel PCM data to I2S. nRF52840 DK board is connected to speaker via I2S player/decoder board. I am able to hear audio but it...
How can I determine the correct value pull-up resistor to be used on the TWIM port?
The nRF52832 reference documentation mention an internal 13k pull-up however I've always...
I would like to create a program that was a mix of ble_app_multilink_central and peripheral_temperature. The program would work as follows: when the button1 of central is...
